Question 6 a) Obtain the transfer function for the block diagram shown, by using the signal flow graph approach. R(s) G₁ Н1 G₂ H₂ G3 H₂ C(s)

Q: In a solar dish, which device converts the thermal energy of fluid into mechanical energy? O a. gas…

A: In a solar dish,  Which devise converts the thermal energy of fluid into mechanical energy.

Q: method of heat transfer principle is used to monitor changes in temperature in contact type…

A: In contact type temperature sensor device, the sensing device is directly connected to the thermal…

Q: What is a “spark spread”? a. The difference between the price of electricity and fuel cost b.…

A: Correct answer is option C Spark spread is defined as the difference between the price of the…

Q: Expalain the four components of electric circuit ?

A: The four main component of any electric circuit is battery which is used to supply voltage to the…

Q: A FET has lpss=4lp and gmo = 10mS then gm express answer in mS

A: FET: It is a semiconductor transistor known as field effect transistor. It works due to single…

Q: Which one of the following, uses dry wood to get a fuel? O a. Fossil Fuel O b. Fuel cell c.…

A: Fossil fuel like coal came from dry wood

Q: Q1/ Choose the correct answer 1.When the coil of Relay is supplied with 12 volts, the common will a)…

A: As per the honour code I will only attempt Q1. Kindly repost the other questions again. THANK YOU!!…

Q: An energy meter connected to an immersion heater (resistive) operating on an AC 230 V, 50 Hz , AC…

A: Given- AC 230 V, 50 Hz, 2.3 units kWh single phase source, Time t=1 hour, Peak square wave source…

Q: The current rating of the fuse is always less than its minimum fusing current O True False

A: We know that fusing factor shoulde be less than one. And fusing factor can be defined as the ratio…

Q: O a. Condensor

A:

Q: Explain the working principle of different types of geothermal energy systems with neat diagram

A: Need to explain geothermal energy system

Q: For a system if the value of peak overshoot is 22 %, then the value of damping ratio Oi is

A: Peak over shoot pos = 22% = 0.22 Damping ratio Zeta

Q: (a) An electrodynamic wattmeter is used to measure the electrical power in a circuit. The diagram in…

A:

Q: method of heat transfer principle is used to monitor changes in temperature in non contact type…

A: The solution is provided in the following section:

Q: What are the benefits of flue gases in thermal station?

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Q: ext A 4 ate Score 0610908 - Introduction to Electrical Phase 1 1 of 20 What happens to current flow…

A: The resistance is increased, then current will also decreased.  Please follow solution.

Q: List out all the major components in a thermal power plant

A: The thermal power plant is used to produce electricity by utilizing the energy of the burning fuel.

Q: Moving Iron meter displays value. (a) RMS (b) average (c) peak (d) instantaneous

A: Moving iron instrument measure RMS value.

Q: Question Why a fuse is also important in our power supply

A: Given: Fuse is a very common electrical safety device. It protects the device from getting damaged…

Q: (a) Determine the colour bands and indicate the resistance range values (minimum - maximum) for each…

A:

Q: How would you describ the flow of Alternating Circuit (AC) and Direct Current?

A: In direct current (DC), the electric charge (current) only flows in one direction and it is…

Q: which one of the following is The rate at which solar energy arrives at the top of the atmosphere a.…

A: Given: Question on what is the rate at which the solar energy arrives at the top of atmosphere?…

Q: What is electrically current

A: It is asked to determine the electrically current. This has been specified with the concept of…

Q: 15-A single phase load located 850 meter from the source the load consumes 80 Amp and operates in…

A: To solve above problem, one should know about resistance calculation of a material. The resistance…

Q: Q2 / explain the operation of spit phase motor

A:

Q: What are the parameters of the ff: Incandescent Lamps Tungsten-halogen Lamps Gaseous Discharge…

A: 1. Incandescent Lamps:   - Light Generation: Incandescent lamps produce light by passing an electric…

Q: 1)Write short notes on the Loading effect due to insertion of voltmeter.

A: According to the given question, it is required to determine the loading effect present due to the…

Q: 1. A 6 ampere supply has a frequency of 25 Hz. Find the instantaneous value of current a. at 0.00530…

A:

Q: b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts,…

A:

Q: 8. The standard measurement data table of a thermocouple is developed when the thermocouple's…

A: thermocouple circuit with one end in an ice bath (0°C) and the other in an unknown temperature. This…

Q: For a system if the value of peak overshoot is 16 %, then the value of damping ratio o is

A: Peak overshoot= 16%

Q: 7. What is the effective value of an AC sine wave current having a maximum value of 4 A peak? 8.…

A:

Q: Which form of renewable energy occupies limited space? O Wind Energy with more turbines O Bio energy…

A: As per bartleby guidelines for more than one question asked only first is to be answered please…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.