Question 5.5 A core contains only oil and water within it. Find the water and oil saturations by using the following data: - Dry weight: 168.3 g - Saturated weight: 203.2 g - Weight of the core after water removal: 184.1 g - Diameter: 3.62 cm - Length: 6.92 cm - Water density: 1.03 g/cm3 - Oil density: 0.79 g/cm3

Question 5.5 A core contains only oil and water within it. Find the water and oil saturations by using the following data: - Dry weight: 168.3 g - Saturated weight: 203.2 g - Weight of the core after water removal: 184.1 g - Diameter: 3.62 cm - Length: 6.92 cm - Water density: 1.03 g/cm3 - Oil density: 0.79 g/cm3

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

calculate the Amott Harvey wettability index for each core and explain the wetting characteristics of each core
Calculate porosity, water, oil, and gas saturations, and lithology from the following core analysis data. How should the calculated saturations compare with the fluid saturations in the reservoir? Oil well core with water base mud. Initial weight of saturated core = 86.4 gm After gas space was saturated with water, weight of core = 87.95 gm Weight of core immersed in water = 48.95 gm Core was extracted with water recovery being 7.12 cc After drying core in oven, core weighed 79.17 gm Assume ρw = 1.0 gm/cc Oil gravity = 40° API
3. The capillary pressure data for a water-oil system are given below: Sw Pc 0.25 35 0.30 16 0.40 8.5 0.50 1.0 The core sample used in generalizing the capillary pressure data was taken from a layer that is characterized by an absolute permeability of 300 md and a porosity of 17%. Generate the capillary pressure data for a different layer that is characterized by a porosity and permeability of 15%, 200 md, respectively. The interfacial tension is measured at 35 dynes/cm.
Given:Flow rate of water = 500 L/minSuspended solids concentration in influent water = 100 mg/LRequired effluent suspended solids concentration = 10 mg/LFiltration rate = 10 m^3/m^2/hrFiltration tank dimensions: Length = 5 m, Width = 3 m, Depth = 4 mCalculate:o Calculate the total suspended solids (TSS) load in the influent water:o Calculate the filtration tank surface area:o Calculate the required filtration tank capacity:o Calculate the required detention time in the filtration tank: Q2) DisinfectionGiven:Flow rate of water = 2000 m^3/hChlorine residual required in effluent = 0.5 mg/LInitial chlorine concentration in influent water = 2 mg/LChlorine decay rate in disinfection tank = 0.05 per hourDisinfection tank volume = 300 m^3Calculate:o Calculate the chlorine demand in the influent water:o Calculate the chlorine dosage required:o Calculate the chlorine dosage rate:o Calculate the actual chlorine dosage rate considering chlorine decay:
Question 4.5 A rock sample has a length of 20.32 cm and a diameter of 5 cm. The pressure profile inside the core sample is given below, where nitrogen of viscosity 0.0178 cP is flowing at a constant rate of 55 cm³/s. What is the permeability of the sample if the flow is in accordance with Darcy's law? 450 400 350 - 300 250 - P [psig] 200 150 100 - 50 1 3. 4 7 8 9. Distance from inlet [in] 6
Please answer the question below. It would be a big help. Thank you. Please be clear with your answer. Box the final answer.
Civil engineering -Hydraulics
A core sample has a cross sectional area of 1 cm2 and a length of 5 cm. Water with a viscosity of 1 cp was flowed through the core under the saturation conditions as follows: Calculate absolute permeability of this core sample Calculate effective permeability to water at the water saturation of Sw = 0.9. Calculate the relative permeability to water at Sw = 0.9. Can you infer from this data if water a wetting or a non-wetting fluid in this core? Why?
In an gas-oil system, the following fluid and sand data are available: h = 12.5 ft , hp = 5 ft Pw= 63.76 lb/ft , po= 47.5 lb/ft3 Bo = 1.1 bbl/STB , µo= 0.73 cp rw = 3 in , re = 1000 ft Ko= 93.5 md Calculate the oil critical rate. using Chaney method.
In a laboratory test of an aquifer material a fully saturated sample of volume 5 liters was taken and its initial weight of 105 N was recorded. When allowed to drain completely it recorded a weight of 97 N. The sample was then crushed dried and then weighed. A weight of 93 N was recorded at this stage. Calculate the specific yield and relative density of the solids. (Assume unit weight of water γγ=9.79 kN/m3) Answers: Specific yield= 16.34%; Relative density of solids = 2.517
Possible solution as soon aS possible Q2// oil formation volume factor = 1.25, reservoir bulk volume 180000 acre.ft Water Calculate; Depth (ft) Porosity% Saturation 1. Pore volume in (acre.ft), (ft'), and (bbl) 4810 13.97 40.5 2. IOIP in reservoir and tank conditions. 19.15 23.89 17.8 4812 4814 4816 11.28 12.49 27.82 4818 16.34 24.94 4820 21.34 21.74
Name:... 6. The pH of the water is measured as 9.3 and the total concentration of carbonate species is found to be 0.00345M. Find the total alkalinity in terms of mg/L CaCO3 Ca = 40 g/mole; C= 12 g/mole; O = 16 g/mole