Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the magnitude of the force P that would result in a 0.18-in. horizontal displacement of bar AB. Use G = 70 x 10° psi for the plastic, and neglect the deformation of the steel frame. A 3 ft B 2 ft Plastic sheet 2.

Question 5 The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the magnitude of the force P that would result in a 0.18-in. horizontal displacement of bar AB. Use G = 70 x 10° psi for the plastic, and neglect the deformation of the steel frame. A 3 ft B 2 ft Plastic sheet 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel [E = 29,000 ksi] tube (2) as shown in Figure P3.7. The inside diameter of the steel tube is d2 = 2.52 in. An external load P is applied to the nylon rod, compressing it. At what value of P will the space between the nylon rod and the steel tube be closed? Nylon rod (1)- Steel tube (2)
A truss is loaded as shown in the figure. Assume AE = 10000
6. A tapered bar of length 600 mm is having cross sectional areas of 650 mm? and 350 mm? at two ends. The bar is fixed at the end having larger area and subjected to axial forces 40 kN which is acting axially outwards at the smaller end and 20 kN, acting at a point 200 mm from smaller end and directing axially towards the larger side. The Modulus of Elasticity of the bar is 700 x 103 N/mm2. Model the bar with three finite elements and Determine i The nodal displacements. ii The stresses in each element. iii The reaction force at the support.
The assembly consists of two 20-mm diameter rods AB and CD, a 30-mm diameter rod EF, and a rigid bar G. The assembly is subjected to the loading shown, with point E located at the midpoint of BD. Take the modulus of elasticity of the rods as 100 GPa. i. Determine the horizontal displacement of point E (indicate direction, left or right). 11. If the applied loads causes the diameter of rod AB to become 20.0022 determine the Poisson's ratio of the material (to 2 decimal places). 350 mm 450 mm A B 40 kN E 60 kN 40 kN DG
SITC. Determine the horizontal displacement (mm) of joint C. 300 lb 300 lb 13 ft B 5 ft 12 ft 13 ft 12 ft
05. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown in the Figure Q5. Given that E=2x10"N/m, A=10mm, L=Im and P-lkN. The horizontal displacement of Joint C (in mm, up to one decimal place) is „JointC P 2AE 7. AE AE Figure 05
SHOW SOLUTION AND ILLUSTRATION
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
7) The load P is located midway between points B and C. P = 1.7 kN. The diameter of the rod at CE is 4.8 mm. The young's modulus of the rod metal = 200 GPa. What is the elongation of the rod CE? 600 mm IB 600 mm 600 mm Elongation of rod EC = units
A simply supported steel beam is loaded with a uniformly distributed load and a torque. The beam has a U-shaped cross section, as shown. Determine the maximum normal compressive and tensile stresses caused by the acting loads. Express your answer in kgf/cm2 and in MPa.
A 90-kg smooth circular cylinder A with a radius of 0.6 m is held in equilibrium by a cord CD and a bar BC of negligible mass. The length of bar BC is 2.4 m. a. Draw the FBD of the circular cylinder and the bar BC.b. Determine the tension in the cord CD.
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.