Question 5 Below is a partial function table of an 8-to-3 priority encoder. It consists of 8 inputs (A7 to Ao) and 3 outputs (F₂ to Fo). Ai has higher priority than Aj if i>j. The only invalid input combination occurs when all inputs are zero. 'X' represents don't-care. A7 0 1 0 0 0 0 A6 A5 A4 0 0 0 X X 1 0 0 0 XX H 1 XX 0 0 0 0 AO A3 A₂ 0 X X xx X 0 0 Oxx X X X 0 0 A₁ Ao Oxxx X 1 0 OXXX 0 X 1 Write out the simplified SOP expressions for F2, F₁ and Fo. F₂ F₁ X X 1 1 1 1 1 0 0 0 : 0 0 Fo X 1 0 1 1 0

Question 5 Below is a partial function table of an 8-to-3 priority encoder. It consists of 8 inputs (A7 to Ao) and 3 outputs (F₂ to Fo). Ai has higher priority than Aj if i>j. The only invalid input combination occurs when all inputs are zero. 'X' represents don't-care. A7 0 1 0 0 0 0 A6 A5 A4 0 0 0 X X 1 0 0 0 XX H 1 XX 0 0 0 0 AO A3 A₂ 0 X X xx X 0 0 Oxx X X X 0 0 A₁ Ao Oxxx X 1 0 OXXX 0 X 1 Write out the simplified SOP expressions for F2, F₁ and Fo. F₂ F₁ X X 1 1 1 1 1 0 0 0 : 0 0 Fo X 1 0 1 1 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

- Explain the difference between binary and BCD using a decimal value 20. - Draw the truth table of the below MUX. For the multiplexer in the figure below, determine the output for the following input states: A=0, B=1, C=1, D=0, So=0, S1=1. Explain your answer. A MUX В 4 to 1 D- si só -How do you explain a DMUX using the above MUX concept?
What are the output values of a 3-bit magnitude comparator with active HIGH output functions AEQB, AGTB, and ALTB for the following input values: 1. a. A = 010, B = 101 b. A 000, B = 111 c. A=010, B = 010 d. A = 110, B = 101 (Ctrl)
Answer complete and correct by hand to get 100% feedback!! Design a comparator that takes two 16 bit numbers A and B as input. The comparator should produce an output of 1 when A is greater than B, and produce an output of 0 otherwise.
A- 1. AND 2. OR A B• 5. XOR A A- 3. NAND 4. NOR O 6. XNORO B 7. 8. A. Butter Inverting Butter Provide the output for the following operators:
Four bit parallel adder is need --- full adder O : 2 • 3 4 the binary number 1001 will be active in decoding output at: O :8 •6 O : 10
Figure Q.5 shows the block diagram of a control system. a) Using block diagram reduction techniques determine the closed loop transfer function of the system shown in Figure Q5. b) Given the individual transfer functions listed below, using Rouths criteria determine the range of values of K which for the system to remain stable. G|(s) = K G2(s) = s+ 4 1 G3(s) = H(s) = s² H2(s) = 2s H3(s) = 1 Hj(s) R(s) C(s) G|(s) G2(s) G3(s) H2(s) + H3(s) +
Electrical Engineering please try all questions. thank you so much (8086/8088 assembly programming) (4a) A program is written to add the values 1000H, 2000H, 00FFH, and 1111H. The partially completed code segment is given below. Complete the partially completed code given below. The final result should be stored in DX. 81 CSEG SEGMENT 82 START: 83 04 MOU AX, 1800H MOU BX, 2000H MOU CX, 08FFH MOU DX, 1111H 85 86 87 08 ; WRITE YOUR CODE HERE 89 10 11 ; return control to DOS MOU AX, 4C00H INT 21H 12 13 ENDS (4b) Write an instruction sequence to implement (08H+16H)/2. Hint: The division by 2 can be accomplished by right shifting the value by 1 bit. (4c) An assembly program is given below. 81 DATA SEGMENT DB 179 02 BINUAL 83 MSG DB This is final exam!' 84 DB ODH, BAH,'$' 05 VAR1 EQU 9983H 86 VAR2 EQU 67H 07 LIST DB 5 DUP (7) 88 ENDS 89 18 CSEG SEGMENT 11 START: 12 MOU AX,DATA MOU DS AX 13 14 15 MOU AX, 05H MOU CX, 10 16 17 LOP1: 18 INC AX LOOP LOP1 19 20 21 MOU AH,4CH; return the control to…
The figure shows a 4 to 1 MUX to be used to implement the sum S of a 1-bit full adder with input bits P and Q and the carry input Cin- Which of the following combinations of inputs to lo, 1₁, 12 and 13 of the MUX will realize the sum S? 4 to 1 MUX lo 1₁ 1₂ 13 S₁ Sp P Q LL F S
Output F ?
Implement a full adder using two 8-to-1 MUXes. Connect X, Y, and Cin to the control inputs of the MUXes and connect 1 or 0 to each data input.