Question 4: Determine the average power delivered and Power factor to network having the following input voltage and current: v = 100 sin(cor +50°) i-20 sin(o +80°)

Q: A Step-down transformer is given and calculate 5:1 120 V 60 Hz V2 1 k? i. Peak load and D.C. load…

A: Since it is a step down transformer therefore V2<V1 and number of turns in primary will be…

Q: Q-4: a) Calculate the values of R and C in the following circuit for maximum average power transfer…

A: The given circuit diagram is shown below,

Q: A complex voltage is represented by v = (10 sin ωt + 3 sin 3ωt + 2 sin 5ωt) volts Determine for the…

A:

Q: A load consisting of a 240 2 resistor in parallel with a (5/18) μF capacitor is connected across the…

A: A parallel RC load is havingR=240 Ω.C=518μF.The supply voltage isvg=120cos(5000t) V.We need to…

Q: For the given circuit calculate: 1- The average power delivered by the source. 2- The power factor.…

A:

Q: 4. Sketch the output Vout for the given input Vin (shown on the right hand side) for each of the…

A:

Q: Three Impedances each of (12-j16) 2 are connected in mesh across a three-phase 435V ac supply.…

A: Note: Resistive Load doesn't absorb reactive power,it only works on active power Inductive and…

Q: 4. Two electrical loads are connected in parallel. Load 1 is 10 kVA at 0.6 lagging power factor.…

A: First load is given 10 KVA at 0.6 PF lagging. Therefore, first load is,

Q: Consider the circuit shown: R1 100 Q V1 sine (A 60 Hz 120 Vrms R2 100 2 4:1 1:2 Calculate the…

A: For easiness , 1st refer all the resistance to source side of the transformer.

Q: A load of 500 kVA operates on 1100 V, 50 Hz mains with power factor of 0.6 lagging. It is required…

A: We have an load with, KVA rating = 500 KVA Vs = 1100 V Frequency (f) = 50 Hz Power factor (cosϕ1) =…

Q: Verify Kirchhoff’s voltage law around the closed loop?

A: Here, we have given an electrical circuit having no. of components connected in series. And, we have…

Q: If a 40-Ω R is in series with a 30-Ω Xc across a 100 V sine wave ac source, calculate: a) impedance,…

A:

Q: In a step-up transformer, the turn ratio is 1: 20. The resistance of 100 2 connected across the…

A: Given information is shown below:To find:

Q: A complex voltage is represented by v = (10 sin ωt + 3 sin 3ωt + 2 sin 5ωt) volts Determine for the…

A: Given that Voltage V = 10 sin ωt + 3 sin 3ωt + 2 sin 5ωt We have to determine a) RMS value. b) Mean…

Q: Write the AC node voltage equations for the following circuit. There is one independent current…

A: The parameters of the given circuit in frequency domain are as follows 10cos2000t=10∠0° V , ω=2000…

Q: A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH.   Assume…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.