Question 4: Consider a sphere with a diameter of 25 mm and a surface temperature of 60°C that is immersed in a fluid at a temperature of 30°C and a velocity of 2 m/s. Calculate the drag force and the heat rate when the fluid is (a) water and (b) air at atmospheric pressure. Explain why the results for the two fluids are so different.

Question 4: Consider a sphere with a diameter of 25 mm and a surface temperature of 60°C that is immersed in a fluid at a temperature of 30°C and a velocity of 2 m/s. Calculate the drag force and the heat rate when the fluid is (a) water and (b) air at atmospheric pressure. Explain why the results for the two fluids are so different.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1 15 points Save Answ Engine oil at 87°C flows over the upper surface of a 5-m-long flat plate whose temperature is 18°C with a velocity of 5 m/s. Determine the total drag force and the rate of heat transfer per unit width of the entire plate (Insert answer for Fp, h and Q) W/m2K kW
Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? I need the solution from fundamental concepts of how the heat flow behaves in the system
i need the answer quickly
Write the comparison between forced and free convection in a non-isothermal system?
2.0 Engine oil at 100°C and a velocity of 0.25 m/s flows over both surfaces of a 0.8-m-long flat plate maintained at 20°C.Determine:(a) The velocity and thermal boundary layer thicknesses at the trailing edge.(b) The local heat flux and surface shear stress at the trailing edge.(c) The total drag force and heat transfer per unit width of the plate.
Engine oil at 100°C and a velocity of 0.20 m/s flows over both surfaces of a 1.1-m-long flat plate maintained at 20°C. Determine: (a) The velocity and thermal boundary layer thicknesses at the trailing edge. (b) The local heat flux and surface shear stress at the trailing edge. (c) The total drag force and heat transfer per unit width of the plate. Determine the velocity boundary layer thickness & at the trailing edge, in m. 8 = i m Determine the thermal boundary layer thicknesses &, at the trailing edge, in m. 8, = i m Determine the magnitude of the local heat flux at the trailing edge, W/m². q" x = i W/m² Determine the local surface shear stress at the trailing edge, in N/m². Ts, L i N/m² Determine the total drag force per unit width of the plate, in N/m. D' = i N/m Determine the magnitude of the heat transfer per unit width of the plate, in W/m. d' = W/m i
Heat transfer
A plastics plant manufactures larges pieces of plastic by continuously extruding thin sheets.As the sheets flow out of the extruder, they are cooled via forced convection and radiation.The plastic sheets are 1 mm thick, 1 m wide, and leave the extruder at a rate of 9 m/min.A fan blows air over the top and bottom surface of the sheet during the first meter after thesheet leaves the extruder. The fan accelerates the air to 3 m/s and the air is known to be at27°C at the fan outlet. At the exit of the extruder, the plastic is at 90°C. The plastic isestimated to have an emissivity of ? = 0.9 and the general surroundings are at 20°C. A) Determine the rate of heat transfer via convection and radiation from the 1-m-longsection of the plastic sheet that is being force cooled. take the surface temperature to be 90°C overthe entire section of interest. B) The density-specific heat product of the plastic is ?? = 1920 kJ m3– K⁄ . What is thetemperature of the plastic at the end of the cooling…
2. Consider laminar fully-developed flow through two smooth isothermal tubes. One tube has circular cross-section the other has square cross-section. The cross-sectional area is the same for both tubes. Show that the convection coefficient in these two flows are related as hcircular 1.088hsquare- %3D Assume that the fluid properties are the same.
Thank you for answering this question. Please you specify each step as soon as possible. Good Luck! Thank you. If you want to cool a thin plate by natural convection quickly, will you hold it as shown in position (a) with the long dimension parallel to the direction of gravity or in position (b) with the shorter dimension parallel to the direction of gravity and why? Assume Laminar flow. (b)
The main body of plenum is a steel vessel of diameter 0.1meters has two semicircle domed ends. During operation is will contain mix of fuel and air at approximately 250OC. The wall of the vessel is 0.03meters thick and the plenum is 0.45meters long. Estimate the rate of heat loss from the vessel when the outside air temperature is 45OC. The thermal conductivity of steel is 45 W/m K and the surface heat transfer coefficient on the air side is 8 W/m2 . On the inside it is 65W/m2 . If it was possible to clad the plenum calculate the reduction in the rate of heat loss. Assume the lagging would be 5mm thick and has a thermal conductivity of 0.05 W/m.
A sphere of 74 mm diameter is moving through the air at a velocity of 0.035 m/s. The surface temperatureof the sphere is uniform at 40◦C and the air temperature is 20◦C. What is the average convection coefficientbetween the sphere and air