Question 36 Determine the tensile steel strain (in 5 decimal places) compatible with concrete strain of 0.003 for a singly reinforced beam 300 mm wide, 680 mm deep reinforced at the bottom with 6-ϕ25 mm bars with effective depth 590 mm. Use f’c = 21 MPa and fy = 420 MPa.

Question 36 Determine the tensile steel strain (in 5 decimal places) compatible with concrete strain of 0.003 for a singly reinforced beam 300 mm wide, 680 mm deep reinforced at the bottom with 6-ϕ25 mm bars with effective depth 590 mm. Use f’c = 21 MPa and fy = 420 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

R.Bars.
Question 33 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 27 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel area for a tension controlled singly reinforced condition in positive bending
A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6 - 28mm dia in two rows, compression reinforcement consists of 2 - 22mm dia, fc' = 27.6MPa, fy = 414.7MPa, d' = 60mm, L = 4m, the Unit weight of concrete is 24.56kN/cu.m If the beam is simply supported carrying a uniformly distributed dead load of 10kN/m, a uniformly distributed live load of 5kN/m, the safe concentrated live load that it could carry acting at the midspan is _________kN. IS 456:2000
Determine the additional longitudinal reinforcements (mm2) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the tensile steel ratio for positive bending. 2. Determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending. 3. Determine the design moment capacity in kN•m of the beam in positive bending.
Calculate the uniform load w (in addition to the beam weight) that will cause the section shown to begin to crack if used as a 28-ft simply supported beam. Use normal weight concrete with L=4000 psi. f = 60,000 psi, E₁=29,000 ksi, and the reinforced concrete weight = 150 lb/ft³. 4 in. 28 ft 4 in. 22 in. 30 in. 2 in. 2 in. 3 #9 ● ||—12 in—-|
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
just answer d to f