Question 3. Find the forces in members BC, AB and BF. 2.5 m Copyright © McGraw-H Education Pemasion required for reproduction or deplay 12.5 kN 12.5 kN 12.5 12.5 kN A E -2 m- -2 m- B ---2m. C G 0

Q: Briefly discuss how each of the following is used by CFD codes to speed up the iteration process:…

A: (a)when CFD codes uses multigridding technique, first the solutions for the equations of motion are…

Q: What information did the Hodgkin and Huxley model provide?

A: It helps to have some background on what happens during an action potential to understand Hodgkin…

Q: Time between job arrivals at a machining station is exponentially distributed with mean 4.4 minutes.…

A: Given:To find:Simulate the system for one 8-hour day.

Q: untuitive methodology (seize and fox) noting they will be different. folowing cases, find the…

A:

Q: Activity 3: The network and communication systems attached to the smart grid, including the routers…

A: Solution

Q: 15% HOW LONG THE RUNWAY must before a plane to reach a takeoff velocity of75 m/sec if it can…

A: soln : - initial velocity = u= 0 m/s          Final velocity = v= 75 m/s Let S is the distance of…

Q: For a given part drawing (fig.2) prepares a part program for a wire electric discharge machine using…

A: For the given part drawing, we can write part program using Fanuc cut language which is based on G…

Q: Two word - wide unsigned integers are stored at the memory addresses OA00 H and OA02 H respectively,…

A: Solution MOV AX, 0; MOV DS, AX ; MOV BX, 0A10H; MOV DX, [0A00H]; ADD DX, [0A02H] MOV [BX], DX; MOV…

Q: 2. Curve fitting: Using the following values, fit a.) a straight line and b.) a quadratic equation.…

A: Straight line Equation are given by ; Y=m×x+C   .................................................…

Q: Which of the following can be used to building up a three-dimensional prototype model layer by layer…

A: According to the given data We need to find Following can be used to building up a three-dimensional…

Q: A die forge press operates an average of 1000 hr/yr. Under a minimal repair concept, machine…

A:

Q: Datum features must be specified in a feature control frame in order of: O Numerical order O…

A: Datum features must be specified in a feature control frame in order of precedence.  Answer - C

Q: forecast sales for april 2023 would be

A: Given; For a product, the actual sales for march 2022 were and forecast is;   15 and 20…

Q: The last 3 compartments in a feature control frame provides the datum references; this is known as…

A: The last 3 feature control frame provides the datum referances, this is known as datum order of…

Q: The diameters of the main rotor and tail rotor of a single engine helicopter are 7.51 m and 1.01 m,…

A: Diameter of main rotor, Diameter of tail rotor, Rotational speed of main rotor, Rotational speed of…

Q: 7. . . is a convenient method used for copying an object while preserving its features: Rotation…

A: In CAD rotation and mirroring can be used to duplicate a selected object, but they are rotated and…

Q: Once aligned at the baseline a second point along the scales where the marks line up is chosen, one…

A: From the diagram of the given scale, the 50th division is in line with the 560th division of the…

Q: Geometric Dimensioning and Tolerancing was designed to insure the proper assembly of Geometric…

A: All questions are solved below. (Answers are mentioned at first and explanation is explained in note…

Q: ite a for loop to print all even numbers betw . Repeat with a while loop. . Write a for loop which…

A: 14. For loop to print even numbers b/w 1 to 20For m=1:20If (mode(m,2))=0display(m)endend15. Repeat…

Q: B1 1.- You have the following manufacturing system: 10% I M1 10% 20% I 90% B21 AS * the total…

A: "Since this is a question with multiple sub parts therefore solutions to only first three sub parts…

Q: Q/ Use the conditions of equilibrium to solve the following problem and find the magnitude of the…

A:

Q: With the following maintenance type, design weaknesses are redesigned to improve reliability or…

A: Predictive Maintenance - It is special type of condition based maintenance where system is…

Q: dimension L4 in mm for assembly condition would be:

A: For the given assembly: L1=22.0±0.01 mm L2=10.0±0.005 mm L3=10.0±0.005 mm It is required to…

Q: Select a suitable material for aircraft wing. Aircraft Wing 1) Product identification and Design…

A: As this is a multipart question , as per the guide lines I am answering the first three parts…

Q: Q#05 (a) :The Lift Mechanism for the package moving is desired to raise (your registration number)…

A:

Q: For a canteen, the actual demand for disposable cups was 500 units in January and 600 units in…

A:

Q: Q5:- Convert the following data into a format that will be accepted by a programmable CNC machine…

A:

Q: The oil temperature is being controlled in a cascade control system as shown in Figure 1. A)…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: It 0:49:29 Determine the magnitude and direction of all support reactions for the pin-jointed…

A: Determine the magnitude and direction of all support reactions for the pin-jointed structure shown…

Q: Name two distinct advantages of theTenergy methods. For the toolbar, press ALT+F10 (PC) or…

A: Definition of energy method-The Energy Method is a general modeling technique, any multidisciplinary…

Q: WRITE SOLUTION HOW DID YOU GET FBD and FBE THANKS

A: How to get the given FBD

Q: devices require accurate pressure and temperature measurement in order to calculate the output of…

A: Givenarea of venturimeter=1.77×10-4m2h=difference of monometric head at point 1 anad 2

Q: Dr. Deduction has a peculiar penchant for using elaborate experimental se- tups and convoluted…

A: Since each element of the system is connected trough a single cord, the acceleration of each element…

Q: 8. What are the main stages of the FEM?

A: This question is based on the concept of Finite element Method.  As per the guidelines we are…

Q: What is the difference between multigridding and multiblocking? Discuss how each may be used to…

A: Computational fluid dynamics is a field in engineering in which analysis and study of the equations…

Q: onvert these ortographic views to isometric. Given are the length for you to visualize.

A: Please refer the following image for the isometric view of the given orthographic views.

Q: outline the foundamental difference between errors that can be largely eliminateed and errors that…

A: Error- The difference between the true value and the measured value is called error. Errors are not…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.