QUESTION 3 IA cable 54m long is attached between supports at A and B as shown in below figure. The lension at support B is equal to the weight of 23m of cable. The angle of inclination of the cable at B is 31°. B.1.I Determine the height of point A above that of point B. D.1.2 If the cable at A passes over a frictionless pulley to form a backstay at 45° to the horizontal, calculate the reaction at the support. (assume a mass of 22kg/m for the cable) y. 31 ground level

QUESTION 3 IA cable 54m long is attached between supports at A and B as shown in below figure. The lension at support B is equal to the weight of 23m of cable. The angle of inclination of the cable at B is 31°. B.1.I Determine the height of point A above that of point B. D.1.2 If the cable at A passes over a frictionless pulley to form a backstay at 45° to the horizontal, calculate the reaction at the support. (assume a mass of 22kg/m for the cable) y. 31 ground level

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 1 Cylinder E has a mass of 80 kg and each cable segment can sustain a maximum tension of…

Q: A E в ED 900 N 0.90.9 1.5

Q: Q.17.8 apart with one end 5 m above the other (as shown in figure below). The cable is loaded with…

Q: for the cable shown. determine the following. a. reactions of the cable b. the sag y at the 45…

A: To find reaction at cable end,sag,and cable length

Q: 13. A 12-m pole supports a horizontal cable CD and is held by a ball and socket at A and two cables…

Q: A cable of uniform cross-sectional area is stretched between two supports 80 m apart with one end 5…

Q: 3. A cable is loaded and supported as shown. Determine the horizontal and vertical components of the…

Q: If the tension in cable DE is 620 N, determine the moments of this tensile force (as it acts at…

Q: 18. Determine the magnitude (N) of the force in cable AD. 19. Determine the magnitude (N) of the…

A: as per our company policy we are required to answer only first three parts. so we request to post…

Q: В 13 20°+ A A D Weight of Crate = X (N) In order to maintain equilibrium, 6. Determine the magnitude…

Q: In Figure 3, the tension in cable AD is 280 lb. Determine the angle between cables AC and AD. y 6 ft…

Q: Determine the tensions in cables A, B, C and D of the cable system supporting a weight of 100 N as…

A: Given ;

Q: In this Question the cable attached to a tower as you can see a) Since f1 = 8m and f2 = 8m, find the…

Q: Q.13.9 Figure below show a cable suspended through simple supports. Assuming point A as origin, the…

Q: 1.5 m 100 N 1.5 m 1. Please refer to the figure at the right. a. Draw the FBD. b. Determine the…

A: To find tension in cable DC , DB and reaction at ball socket joint A

Q: THE CABLE ABCD IS HELD IN THE POSITION SHOWN BY THE HORIZONTAL FORCE P. DETERMINE P AND THE FORCE IN…

Q: The left support of the cable shown is located 10 m below the right support. The lowest point on the…

A: Consider the free body diagram;

Q: 4. The uniform rod in figure shown weighs 420 kN and has its center of gravity at G. Determine the…

Q: 100 m 3. A cable supports a load of 50 kg/m uniformly distributed along the horizontal and is…

A: First, calculate the distance of the lowest point from each end. Then calculate the horizontal…

Q: Solve for the reactions and the tensions in cable segments. 5 Н. Hi 1 25 3. V5 V1 30 k 50 k 40 k 4 @…

Q: The weight of 1 m of the parabolic cable with the liquid in the figure It carries a 5 kN pipe. a)…

Q: A cube (SG = 3.2) with side 1.5m is attached to a cable. The cube was completely submerged into…

Q: Determine the tensions in cables A, B, C and D of the cable system supporting a weight of 100 N as…

A: Given data Find force in member A, B, C and D.

Q: Three cable tensions T1, T2, and T3 act at the top of the flagpole. Given that the resultant force…

A: Given data R = −400kN,

Q: distributed load of 7 kN/m and the sag of the cable measured from the higher end is 6 m. Calculate…

A: To determine: Horizontal tension in the cable Maximum tension in the cable Given, Uniformly…

Q: distributed load of 7 kN/m and the sag of the cable measured from the higher end is 6 m. Calculate…

Q: The resultant tensions at the ends of the uniform flexible cable are 8000N and 8800N, respectively.…

A: Length of cable=300m Weight of cable=5000N

Q: The cable system shown in Figure 4.25 carries a uniformly distributed load of 5 kN/m * between the…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: A 100N load is supported by a strong bar as shown in the figure. The tension in the cable is 200N.…

Q: Consider P₁ = 3.7 the cable shown in (Figure 1). Suppose that kN, P₂ = 5.5 kN.

Q: distributed load of 7 kN/m and the sag of the cable measured from the higher end is 6 m. Calculate…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

UESTION 3
A cable 54m long is attached between supports at A and B as shown in below figure. The tension
at support B is cqual to the weight of 23m of cable. The angle of inclination of the cable
at B is 31°.
.I.I Determine the height of point A above that of point B.
.1.2 If the cable at A passes over a frictionless pulley to form a backstay at 45° to the horizontai,
calculate the reaction at the support. (assume a mass of 22kg/m for the cable)
y.
ground level
3.2 A cable is suspended between two points P and Q which are 200m horizontally apart. P and Q
are on the same level and 8m higher than the lowest point in the cable.
3.2.1 Find the maximum tension in the cable and the slope at the support if the cable carries 10kN
per horizontal metre.
3.2.2 What is the tension 25m from P.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Height of point A above that point B

VIEW

Step 3 Height of point A above that point B

VIEW

Step 4 Height of point A above that point B

VIEW

Step 5 Reaction at support A

VIEW

Step 6 Calculation for reaction at support A

VIEW

Step 7 Answer

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve it !!
A sa p
In Prob. 3.59, determine the perpendicular distance between cable AE and the line joining points D and B.(Reference to Problem 3.59):The triangular plate ABC is supported by ball-and-socket joints at B and D and is held in the position shown by cables AE and CF . If the force exerted by cable AE at A is 55 N, determine the moment of that force about the line joining points D and B.
for the cable shown. determine the following. a. reactions of the cable b. the sag y at the 45 kips load c. cable length
Given: The structure shown below is cantilevered at the Point A and welded at point B. In addition, the magnitude of the tensile force in cable GE is 2,000 N, and member BC is parallel to the x axis. 6 m D B. cable 12 m C 15 m 10 m 100 KN Required: a) Determine the vector components of the force in cable BD. b) Draw a free body diagram of the orange structure. c) Determine the components of the reactions at point A.
Given: The structure shown below is cantilevered at the Point A and welded at point B. In addition, the magnitude of the tensile force in cable GE is 2,000 N, and member BC is parallel to the x axis. y 6 т G В cable 6 m 6 т 15 m 10 m 40 KN Required: a) Determine the vector components of the force in cable GE. b) Draw a free body diagram of the orange structure. c) Determine the components of the reactions at point A.