Question 3 Figures Q3(a)(i) and Q3(a)(ii) below show the biasing of a transistor to achieve certain signal conditioning functions. Given that the VBE = 0.7 V, B = 99 and VCE(sat) = 0.3 V. (a) Vcc = 10.7V Vcc = 10.7V 1kn 10kn 10kn 10kn 5.7V oMm 5.7V oMM B = 99 B = 99 2kn 2kn Figure Q3(a)(i) Figure Q3(a)(ii) (i) State the conditions necessary for a transistor to operate in an active mode and in saturation mode. (ii) Interpret the above biasing circuits using the DC load analysis and determine which one of the two circuits, would you use to implement a simple switching circuit. You need show all the steps involved in carrying out the analysis for both the circuits.

Question 3 Figures Q3(a)(i) and Q3(a)(ii) below show the biasing of a transistor to achieve certain signal conditioning functions. Given that the VBE = 0.7 V, B = 99 and VCE(sat) = 0.3 V. (a) Vcc = 10.7V Vcc = 10.7V 1kn 10kn 10kn 10kn 5.7V oMm 5.7V oMM B = 99 B = 99 2kn 2kn Figure Q3(a)(i) Figure Q3(a)(ii) (i) State the conditions necessary for a transistor to operate in an active mode and in saturation mode. (ii) Interpret the above biasing circuits using the DC load analysis and determine which one of the two circuits, would you use to implement a simple switching circuit. You need show all the steps involved in carrying out the analysis for both the circuits.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A/Q3
Please provide Handwritten answer
8.
answer part b,c, and d
Q4. For the circuit shown in Figure Q4: i) What is the type of MOSFET and the amplifier configuration? ii) Find the Q-point (Ip and Vps) iii) What is the device transconductance, gm? iv) What are the voltage gain and output voltage? v) Draw the input /output voltage waveforms showing the phase relationship between them. Be sure to label them properly. +20V IDON = 15 mA@ VcsON = 6V VGSTH = 1V 1kQ Rp C2 10M2 Ro1 out Vin 3.3MQ Ra, 47003 Rs 50mV Figure Q4
Check Answer: 103000 This question will check your understanding of Lecture 4 - Nodal Analysis (Section 3.10 of Electronics: A Systems Approach) This is question 4 of 5. Vs1 = 127 V, VS2 = 128 V, R₁1 = 61 Q, R₂ = 69 Q, R3 = 86 Q2, R4 = 31 Q and R5 = 69 Q. The nodal equations for the circuit are: VS1-V₂ 2 V3-V₂ 0-V₂ + + R₁ R₂ RA = 0 and Enter the value for V3. Check V₂-V3 R₂ Choose... + 7 + VS2-V3 0-V3 R3 + R5 - 0 This question will check your understanding of Lecture 4 - Nodal Analysis (Section
4. A Darlington transistor is essentially an array of two transistors connected as shown below. Assume both transistors follow our simple model with a current gain of B=100. Determine the maximum value of R2 that will just saturate the transistors, and pass full current through the load resistance R1. v2 V2 R2 PULSE (0 5 0) Q2 NPN R1 10 Q1 NPN V1 24
Q3. The transistor parameters in the ac equivalent circuit shown in the figure below are ß1 = B2 = 100, VA1= VA2 =00, Vr= 0.026 v, Icoi = 0.5 mA, and Ico2 = 2 mA. (a) Find the small-signal voltage gain Avi = Vo1/Vi . (b) Determine the small-signal voltage gain Av2 = Vo2/Vo1. (c) Determine the overall small signal voltage gain A,= Vo2/Vị . RE2 C4 k2 Solution: o Vo2 Vol Q2 Rci = 4 k2
Q3 Figure 3 shows two current mirrors based on MOSFET. Derive a formula relating the input current Iin to the output current Iout for the current mirror on the left of Figure 3 stating any assumption. (a) (b) Derive the input resistance Rin and output resistance Rout for the circuit on the left of Figure 3. State any assumption. (c) Derive a formula relating lin and Iout for the circuit on the right of Figure 3 assuming that M1 and M2 are identical, and that the length and width of the channel for the transistor M4 are double respect to those of M3. State anv assumption. VDD M3 M4 out Iout M1 M2 M1 M2 Vss = 0 V Vss = 0 V Figure 3
In the circuit given in the figure, Vcc = 15 V, R1 = R2 = 10kΩ, RE = 1KΩ, RL = 0.5kΩ and transistor parameters are given as VBE = 0.7V, ßdc = ß0 = 100. a. Calculate the values of DC bias currents and voltages (IBQ, ICQ and VCEQ). b. Draw the small signal equivalent circuit of the circuit using the hybrid model of the transistor. c. Derive the input impedance expression of the circuit and calculate its value. d. Derive the AVI and AVG voltage gain expressions and calculate their values. e. Derive the current gain expression AI = I0 / Ii and calculate its value. Compare this value you have calculated with the value you will calculate using the expression Aİ = Zi AVI / RL.