QUESTION 3 Figure Q3 shows a steel beam structure, which is pinned, roller and fixed supported at A, C and D respectively. The beam is subjected to the concentrated load at B and uniform load at D. The relative plastic moments of resistance for all spans are shown in the figure. a) Draw the mode of failure mechanism for the beam structure. (CO2, C3, PO2, WP1) Marks b) Determine the maximum plastic moment for the beam structure. (CO3, C4, PO2, WP1) 10KN 15KN/m A 2Mp C 3Mp 4m 4m 3m 3m Figure Q3

QUESTION 3 Figure Q3 shows a steel beam structure, which is pinned, roller and fixed supported at A, C and D respectively. The beam is subjected to the concentrated load at B and uniform load at D. The relative plastic moments of resistance for all spans are shown in the figure. a) Draw the mode of failure mechanism for the beam structure. (CO2, C3, PO2, WP1) Marks b) Determine the maximum plastic moment for the beam structure. (CO3, C4, PO2, WP1) 10KN 15KN/m A 2Mp C 3Mp 4m 4m 3m 3m Figure Q3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown in fig. the bar carries a load of 20 KN at B. the cross section areas of steel and copper are 200 mm2 and 400 mm2 respectively find the stress in each rod ?if Es=210 GPa and Ec=83 GPa Copper rod 2m Steel rod- -1 m- 1m 2 m m- B 20 KN
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 20 x 10-3 mm while those at CD decrease 80 x 10-3 mm in the 250-mm-gage length. Using E = 180 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 50 mm, b 120 mm, and c = 70 mm. gage length a mm B b mm c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 103 mm while those at CD decrease 80 x 10 ³ mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa. Given: a = 40 mm, b 130 mm, and c = 90 mm. gage length a mm b mml c mm
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 40 x 10 -3 mm while those at CD decrease 80 x 10 -3 mm in the 230-mm-gage length. Using E = 150 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a = 50 mm, b = 140 mm, and c = 80 mm.
Problem 2: Analyze the following, state the determinacy and the stability. 3. 2. - hinge hinge hinge-
Help
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
Answer in two decimal places please
I need the answer as soon as possible
In a laboratory test of a beam loaded by end couples, the fiber al layer AB as shown are found to increase 30 x 10 8 mm while those at CD decrease 60 x 10 -3 mm in the 280- mm-gage length. Using E = 150 GPa, determine the flexural stress at the bottom fiber. Answer must be in MPa, Given: a = 50 mm, b = 120 mm, and c - 80 mm. gage length a mm A b mml Cmm
Refer to the composite body shown in Figure IV.a) Solve for the reactions at pin support at A and roller support at B. b) Determine the reactions at each connection- B,C,D.