Question 3 An electron enters the uniformly electric field of parallel plate with velocity equal to (2 x 10'm/s) and perpendicular to the field line the distance between two plate equal to 5.0 cm, and the electric field between the two plate is E=25000 N/C, the length of the plates are 6.0 cm 1)How much work must the external force do to move the electron from the positive plate to the negative plate? 2) Determine the time it takes for to move through the plates? 3) Calculate the acceleration of the electron as it falls back to the positive plate?

Question 3 An electron enters the uniformly electric field of parallel plate with velocity equal to (2 x 10'm/s) and perpendicular to the field line the distance between two plate equal to 5.0 cm, and the electric field between the two plate is E=25000 N/C, the length of the plates are 6.0 cm 1)How much work must the external force do to move the electron from the positive plate to the negative plate? 2) Determine the time it takes for to move through the plates? 3) Calculate the acceleration of the electron as it falls back to the positive plate?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Natural gas is a mixture of 95% of methane and 5% of a. Ethane and Propane O b. CO2 O c. Ethane and Pentane O d. Methane and Butane
2. A bank of nickel-cadmium cells is used as the emergency lighting supply for a hospital. There are 100 cells connected in series and each has an A-hr rating of 120 A-hr. The bank has to be replaced, and the manufacturer is no longer supplying nickel-cadmium cells. It is decided to replace the cells with lead-acid cells. How many lead-acid cells will be required if each has an A-hr rating of 60 A-hr, and how should they be connected?
List the name of some Initiator & Emulsifier
Determine the maximum value of R_ for proper operation of the zener diode. 2200 20V Vz =10V Pzm = 400mW O 1628 ohm O 1835 ohm 2422 ohm 1784 ohm
Determine zener diode voltage value as well as the ripple percentage of the circuit below with 240Vpp. Please answer it clear with complete solutions. Thank you. This subject is Electronics 1.
Please answer quickly thank you
What is wrong with this diode? XMM1 Open Not enough data Short 1 2 Nothing IDEAL_DIODE Multimeter-XMM1 X 35.733 ΜΩ V 52 dB A Set... ( .)
The diode starts to conduct when the voltage across it is 0.6 V. Vin is a variable DC voltage source. R1 = 11.6 0 and R2 = 9.8 0. www R1 R2 Va If Vin is increased from zero, at what value of Vin volts will the diode start to conduct. Express your answer accurate to two decimal places.
When the switch is in Position 1, calculate how long will it take the capacitor to fully charge. E. Also, Calculate how long will it take the capacitor to fully discharge when the switch is moved to Position 3. With the battery connected, move the switch to Position 1. After the time determined in Procedure 12, move the switch to Position 3. Describe what happened below. Ensure you include the terms “charge” and “discharge” in your answer.
-2€ Cost 2 (8) (Sinzt + Coszt ) -3€ @ 2"(2Gsst-35sin5t) 2t 3 L £(6) ...
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm