Question 3 A steel column of hollow circular cross section is supported on a circular steel base plate and a concrete pedestal. The column has outside diameter d= 250 mm and supports a load P= 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness t? Based upon your result, select a thickness for the column. (Select a thickness that is an even integer, such as 10, 12, 14, ..., in units of mm.) (b) If the allowable bearing stress on the concrete pedestal is 11.5 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load Pallow that the column with the selected thickness can support? d Column Base plate

Question 3 A steel column of hollow circular cross section is supported on a circular steel base plate and a concrete pedestal. The column has outside diameter d= 250 mm and supports a load P= 750 kN. (a) If the allowable stress in the column is 55 MPa, what is the minimum required thickness t? Based upon your result, select a thickness for the column. (Select a thickness that is an even integer, such as 10, 12, 14, ..., in units of mm.) (b) If the allowable bearing stress on the concrete pedestal is 11.5 MPa, what is the minimum required diameter D of the base plate if it is designed for the allowable load Pallow that the column with the selected thickness can support? d Column Base plate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
ANSWER THE PROBLEM GIVE WHAT IS ASKED, SHOW YOUR SOLUTION, AND BOX THE FINAL ANSWERS. WRITE IT ON A CLEAN PAPER CLEARLY. I WILL GIVE THE FEEDBACK RATING AS POSSIBLE, YOU CAN ANSWER IT. THANK YOU
With illustrations please and detailed Solution.
Complete solution please
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
Consider the following uniformly loaded simple beam. The beam has a span length L = 2.5 m, the load has a uniform intensity q = 3.8 kN/m, and the maximum bending stress o = 60 MPa. q = 3.8 kN/m L = 2.5 m The cross section of the beam is square, and the material is aluminum having modulus of elasticity E = 70 GPa. (Use the formulas of this example. Use available deflection formulas. All beams have constant flexural rigidity EI.) Calculate the maximum deflection 8, max: (Enter the magnitude in mm.) mm
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
Determine the normal stress in the steel plate. Gusset plate is 16 mm thick column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60mm 8-mm plate thickness 183.45 MP 0148.53 MPa 58.33 MP3 22282 MP A 14583MP
(a) 128.5 GPa circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The axtension of rod is 0.09 mm and change in diameter is 0.0045 mm. What is the Poisson's ratio of the material of the rod? (a) 0.35 (b) 0.33 (c) 0.32 (d) 0.30
answer pls in hand written solution