Question 2: We have 10KVA, 4800/240 V, 50HZ single phase transformer. R1 is measured as R1 = 20 2 From the short circuit test (secondary short circuited) : Usc = 179V, Psc = 181W, Isc = 2A From the no load test (secondary open circuited): U20 = 240V, P20 = 60W, I20 = 1,5A When the output power is 10KVA with cosp2=0,9 inductive, find: a) Calculate the transformer parameters b) Iron loss and Copper loss c) Output power

Question 2: We have 10KVA, 4800/240 V, 50HZ single phase transformer. R1 is measured as R1 = 20 2 From the short circuit test (secondary short circuited) : Usc = 179V, Psc = 181W, Isc = 2A From the no load test (secondary open circuited): U20 = 240V, P20 = 60W, I20 = 1,5A When the output power is 10KVA with cosp2=0,9 inductive, find: a) Calculate the transformer parameters b) Iron loss and Copper loss c) Output power

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

don't copy
need quick solution please
Can you solve D and E
A 120 kVA, 1350/330 V single phase transformer has the following parameters: R1 = 0.34 Q, X1 = 0.59 0, R2 = 0.014 Q, X1 = 0.029 Q, Rc = 380 and Xm = 320 Q. The no load current is 4.7 A at a power factor of 0.36 lagging and the no load losses are 4.6 kW. For a full load and 0.9 power factor lagging with 300 V load terminal voltage, determine (a) equivalent circuit parameters referred to primary side, (b) percentage regulation and (c) full load efficiency. O:01 AM
The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short- circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) 8000 V V= 489 V I0.214 A 2.5 A P= 400 W P= 240 W Find the impedances of the approximate equivalent circuit referred to the primary side, and sketch the circuit.
A three-phase uncontrolled bridge rectifier delivers power to a resistive load of 10.The output voltage of the rectifier is 400 V DC. The rating of source side of three phasedelta – star transformer is
17 A single-phase transformer has a turns ratio of 5000/3000. A direct current voltage of 140 Volt is applied to the primary winding, compute the voltage of the secondary winding.
56. A single phase thyristor adjust line spacing converter with a resistive load is shown below: V₂ = V sinest SCR ER R V₂ (B) 1.11 (D) 1.44 If the supply voltage is 230V (rms) at 50 Hz, calculate ripple factor for firing angle a-45" and R - 100 9. (A) I (C) 1.21
3 phase full convertor..
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
A three-phase uncontrolled bridge rectifier delivers power to a resistive load of 102.The output voltage of the rectifier is 400 V DC. The rating of source side of three phasedelta - star transformer is,
The table below shows some performance parameters of a certain power transformer. Full-load voltage regulation Full-load copper loss Load power factor 0.5 Lagging 5% The Maximum noccihle voltage regulation of the trane former is: 5.033 96 5.385 9 3 96 4.134 % 21 21