Question 2 The vertical shaft and the pulleys keyed to it in Figure Q2 may be regarded as weightless. A constant angular velocity is used to rotate the shaft. The known belt pulls are shown, and the three pulleys are firmly keyed to the shaft. Calculate the required diameter of a solid circular shaft if the operating stress in shear is 50 MPa. Because the bearings and pulleys are close together, neglect shaft bending. 250 mm 350 mm 1 -500 mm- -3 kN 1 kN 1 kN 1.25 KN

Question 2 The vertical shaft and the pulleys keyed to it in Figure Q2 may be regarded as weightless. A constant angular velocity is used to rotate the shaft. The known belt pulls are shown, and the three pulleys are firmly keyed to the shaft. Calculate the required diameter of a solid circular shaft if the operating stress in shear is 50 MPa. Because the bearings and pulleys are close together, neglect shaft bending. 250 mm 350 mm 1 -500 mm- -3 kN 1 kN 1 kN 1.25 KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid steel rotating shaft in the figure is supported at B and C, and is driven by a gear, not seen, which is linked to spur gear D which has a pitch diameter of 150 mm. The drive gear force F acts at a pressure angle of 20 degrees. The shaft transmits a torque to point A of Ta-350 N.m. The properties of machined steel shaft are Sy-420 MPa and Sut-560MPa. Use a safety factor of 2.5 and determine the minimum allowable diameter in section B and C. Assume sharp felt radii at the bearing shoulders to estimate the stress concentration factors.Explain.
A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the angle of twist in degrees
Figure shows a hollow quarry drill bit in operation. When drilling, it experiencesresistive torques T1 = 10 kNm at A, T2=26kNm at B. A pushing compressive force (in x direction)is also applied 25 kN at C generating a compressive stress σxx in AB and BC. The hollow part of the drill bit is used to pump coolant at a pressure such that it generates a circumferential stress of Oyy= 20 MPa. The dimensions of the drill are given in Table .i The maximum principal stress for part AB (in MPa)ii The maximum principal stress for part BC (in MPa)iii The part of the drill (AB or BC) and location of brittle failure plane withrespect to drill bit axis.
Please help with the stress, mohir circle, etc. Thank you
A 16 in. diameter motor pulley is running at 600 rpm with a 6 in diameter shaft transmitting power to an agricultural locomotive. If the dimensions of the square key is 0.5 x 3 in, what is the maximum force in the pulley’s belt that can be transmitted if the shear stress is limited to 8500 psi and bearing stress limited to 4000 psi?
Please answer quick. Thanks
with diameter d = 38 mm transmits 37 kW to a gear Calculate the required speed of rotation (number of at B. The allowable shear stress in the steel is 40 MPa. X7-3 A motor driving a solid circular steel shaft revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm B
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter d, / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, G, = 28 Gpa. %3D Rs Rp
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the diameter of the shaft required to transmit 45 kw at 120 rpm. The maximum torque is likely to exceed the mean by 30% for a maximum permissible shear stress of 55. Calculate also the angle of twist for a length of 2m.
Solve the problem and don't copy wrong solution from another website!!
Design