Question 2: The cross-sectional area for the lattice rods in the figure is A=120 mm2, the modulus of ela if the singular loads shown in the figure are affected, how many mm is the length of the BC rod under the influence 120 kN

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: 2. If Tc= (-5) find TF. TK and TR.

A: Given:  TC=-5

Q: Q1/ A. Write the force system for each one of the following? JIL

A: Given:-  To Find:-  Type of force system

Q: X 300 mm D 800 mm B

A:

Q: In the figure shown, compute the following : 75 mm 75 mm E 75 mm-

A: Given Shaded area To find Centroid X axis Centroid Y axis

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: 400N 200 Z00 N さ

A: Given Data :

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: 3

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: Q 4/ Give the names of the components to the parts in the vehicles According to the figures. Cutch 4…

A: Data given-

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: X 300 mm D 800 mm B

A: For constant angular velocity, angular acceleration is zero,

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: In the engine system shown, the lengths of the connecting rode (that is the length of BD) and the…

A:

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: how did the equation simplify to a = 0.984?

A:

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: 4 in 2 in 4 in 8 in -12 in 16 in-

A: Given data To determine the moment of inertia and radius of gyration about x and y axis

Q: Describe the Parallel-Axis Theorem for an Area?

A:

Q: Q3: Draw the geometry shown in figure below . 88 38 12 719 -28 12 50

A:

Q: Move the forces in the shape to point a

A:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: D= 1.75 in d= 0.75 in r= .120 in

A: Calculate D/d and r/d ratio, Fr calculating the stress concentration factor we use the…