Question 2 , Given the single line diagram of a three phase balanced system. 1) Find the per-unit equivalent diagram, using Sbase=25MVA and Vbase_Gen= 13.2KV. 2) Find the voltage at the generator end in KV if the voltage at the load terminal is 12kV full load and pf of 0.9. GENERATOR TRANSFORMER TRANSFORMER MOTOR 15,000 kVA 13.0 kV T1 T2 X" = 15 percent LINE X = 65 Q MOTOR 13.8kV 10,000 kVA 25.000 kVA 25.000 kVA

Question 2 , Given the single line diagram of a three phase balanced system. 1) Find the per-unit equivalent diagram, using Sbase=25MVA and Vbase_Gen= 13.2KV. 2) Find the voltage at the generator end in KV if the voltage at the load terminal is 12kV full load and pf of 0.9. GENERATOR TRANSFORMER TRANSFORMER MOTOR 15,000 kVA 13.0 kV T1 T2 X" = 15 percent LINE X = 65 Q MOTOR 13.8kV 10,000 kVA 25.000 kVA 25.000 kVA

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
Here is a single phase transformer, 15 kVA, 15000/380 V, 50 Hz has Ze-0.02+j0.05 perunit, R. 50 perunit, and Xm =30 perunit, (per unit = actual value/base value), for scaling of the problem. (pu). A) Compute and draw the equivalent circuit components in Qs referred to the low-voltage side, B) Low voltage side is connected to a load of 4L 90° (lagging) and HV side is supplied by 15KV, compute voltage drop on the load V2 and voltage regulation VR.
1. An abrupt Si p-n junction has Na = 1017 cm³ on the p side and Na = 1016 cm³ on then side. At 300 K, (a) calculate the Fermi levels, draw an equilibrium band diagram, and find Vo from the diagram.
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
3) A three-phase transformer of 60 kVA (three-phase power), 13200/480 V (line A line) in delta-strella connection has a resistance of 0.02 PU and a reactance of 0.08 PU. For this transformer, calculate: a) The voltage regulation at full load and F.P. 0.85 in delay. (b) The regulation of voltage voltage to full cargo and F.P. Unitarian. c) The voltage regulation at full load and F.P. 0.85 in advance.
For the determination of one phase parameters of 20kVA 20000 / 480V, 60Hz transformerData were obtained by performing the following experiments.Blank running test: Vb: 480V Ib: 1.51A Pb: 271WShort circuit test: Vk: 1130V Ik: 1A Pk: 480Wa) Find the approximate equivalent circuit parameters with respect to the primary.b) When connected to the transformer to a load with a power factor of 0.8, it draws 42A at 480V. ItCalculate the yield in the conditions.
The capacity of each transformer in a 3-phase A/A transformer bank is 250 kVA. If a balanced star load is connected across it and is taking 750 kVA. Now due to some reasons, the transformer bank starts operating as open delta connection. The percentage overloading on the bank in open delta connection is
Figure below shows a power system. The rating of generators and transformers are:G1:25MVA, 6.6KV, jO.2 p.u. G2:15MVA, 6.6KV, jo.15 p.u. G3:30MVA, 13.2KV, jo.15 p.u. T1: 30MVA, 6.6A- 115Y KV, jo.1 p.u.T2: 15MVA, 6.6A- 115Y KV, jo.1 p.u. T3:single phase units each rated 10MVA, 69/ 6.9 KV, jo.1 p.u. Find te reactances in p.u, take a base of 30MVA, 6.6 KV in the circuit of G1 .=.XG1 G2} 4 A lubu T2 T1 T3 G1 G3 j120 2 j90 N
It is bartleybe's policy that if questions objective than you need to solve at least first 3 questions.
Connect the wires into a OPEN DELTA configuration .