Question 2: Given: A (8, 0, 0) - a downward force "P" is acting vertically at A B (3, -6, 4) D (0, 4, -2) P = 120kN Required: a. Find the compressive force in member AB b. Find the tensile force in member AD +x 1200KN

Q: Consider a rigid rod that is subjected to two external forces and is fixed to the wall at A. The…

A:

Q: Examine the rod below. It is fixed into a wall at the left hand end. From the wall to point B is…

A: Given: The force at D, P = 221.6 N The force at D along y-axis, Fy = 400 N The force at D along…

Q: A tower of 20 m, height is supported by three ropes shown in figure below. If the force of AB Is 50…

A:

Q: 7ft Corce докл 66° 5.30 look 50 g 80° G 36 30 Yo >15 4ft 3ff for all member f 66 2ft ? E

A:

Q: Example 1- determining the components of the specified forces in the direction of the x and y axes…

A: Draw the free body diagram of the force system.

Q: 2.) The plate is supported by a pin in a smooth slot at B. What are the reactions at the supports?…

A: Given:The diagram of the problem is given below;

Q: Determine the shear stress Try that acts at point A. Express your answer to three significant…

A: Solution: GIven Data: d = 40 mm Fx = 1350 N Fy = 540 N Fz = 920 N

Q: 6. Three wires are used to support the 150-lb force. The wires AB and AC are made of steel, and wire…

A: Tension occurred in a cable due to stretch or pulled It is an internal force that acts all along the…

Q: The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of…

A: Given data: The modulus of elasticity in aluminum bar is E1=70 GPa=70×103 MPa The modulus of…

Q: Hinge supported beam is loaded by two concentrated forces and a couple. M F, F2 1 Given: /4=20cm;…

A:

Q: What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant…

A: Ans-a

Q: -300lb 200lb 300lb 45 -150lb A A 30° -y FORCE Ibs F= F.Sin( e) A M= Fxd Couples F,= F.Cos( e )…

A: Draw the FBD for the given question.

Q: As shown, an L-shaped bar is supported by a pin at joint A. The bar's dimensions are aaa = 620 mmmm…

A: Introduction We shall compute the real orientation of the applied force at an angle in this…

Q: The bar AC is supported by a joint at A and a pin B that is free to slide in the same direction…

A: Given; Length, L1 = 2.7 m Length, L2 = 1.7 m Angle, α = 13o Angle, θ = 25o The force, P = 68 kN

Q: Q2: A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside…

A:

Q: As shown in the figure, the member is anchored at A and section AB lies in the x–y plane. The…

A: Part 1 To calculate moment about AB we have MAB=μAB.γAC×FUnit vector is given…

Q: tipod shawn supports that ball and rocket joints are used to mount the tripud points BID,and C. oad…

A:

Q: Q1. Links BC and De are made of the same material (E = 29x106 psi) %3D and have the same cross…

A: The free-body diagram of the figure is given below:  Taking moment about point F :…

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a = 2 ft • b= 4 ft c= 1 ft then, what…

A: Consider the free body diagram of member AC, Here,

Q: Find the force P which is applied on point B of the triangle ABC, as :shown in the figure below P=?…

A:

Q: The steel box wrench (E-29,000ksi, v=0.32) loaded with a 40-lb horizontal force and a 25-lb vertical…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: 4 m 5 m 4 m B 4 m 80 kN 60 kN fınd the forces in members (BC,BE and DE) ? T or C p 10:36

A:

Q: 3. Find the force applied to the truss member CD, CE, and FG in the following figure. C 30⁰ G →→5m…

A:

Q: bar of square cross section is subjected to point loads of P1, P2, P3 and P4 as shown here.  Find…

A:

Q: with the following modifications: Add an additional force P = 20kN acting downwards at point B

A: Add an additional force P = 20kN acting downwards at point B.Determine the force in each member of…

Q: Hinge supported beam is loaded by two concentrated forces and a couple. М F, F, 2 Given: 11=40cm;…

A:

Q: The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are 0xx = -A(L - x)y, and oxy =…

A:

Q: Problem 3. As shown in the Figure below, please determine the internal force in the middle of AB,…

A: OA = 15 cmOB = 30 cmOC = 60 cmW = 40 NWo = 60 NF3 = 1214 NFM = 1236 NRequired:FAB

Q: Determine the force in members FH, EH and EG shown in Figure 1 using method of sections. 1 kN 3 kN 3…

A: [Bartleby policy]: Since you have asked multiple questions, we will solve the first question for…

Q: The weight of the linkage AB =BC= 20KG .Find the force acts on bar BC -875 mm- B 400 625 mm 30 60 F…

A:

Q: The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at…

A:

Q: Find the force P which is applied on point B of the triangle ABC, as * :shown in the figure below

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.