QUESTION 2 F(A, B, C, D) = Em(0,3,5,8,10,12,13) + Ed (6,7,9,15) a Implement the above function using a 2-1 multiplexer. Connect signal A to the multiplexer select input. Write expressions for the multiplexer inputs 10 and 1. b. Implement the above function using a 16-1 multiplexer. Write expressions inputs 10 to 15.

QUESTION 2 F(A, B, C, D) = Em(0,3,5,8,10,12,13) + Ed (6,7,9,15) a Implement the above function using a 2-1 multiplexer. Connect signal A to the multiplexer select input. Write expressions for the multiplexer inputs 10 and 1. b. Implement the above function using a 16-1 multiplexer. Write expressions inputs 10 to 15.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 1SQ: Describe what is meant by sequence control.

See similar textbooks

Similar questions

Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
Needs Complete solution with 100 % accuracy.
The image shown in the image below is a digital Multiplexer circuit. i.Explain its function
There exists one or more discrete ime signal. What is it control system ? (a) discrete time or (b) continuous time
Q2 Figure Q2 shows a Linear Feedback Shift Register circuit. Write down the VHDL entity associated with a 6-bit shift register with the inputs and outputs as shown in Figure Q2. (a) (b) Write down a VHDL architecture for a 6-bit shift register. 6-bit parallel out shift register clk d reset serial_in Figure Q2
2. Consider the following circuit D å lå a. Find the expressions for D, T, Qo*, Q₁*. b. Write the transition output table. c. Draw the state diagram of the circuit. d. Is this a Mealy or Moore machine? Explain. T 21 a la 1
Q1/B/ Determine the analog voltage output for the Figure shown below if the waveforms representing a sequence of 4-bit numbers in the Figure below are applied to the inputs. Input Do is the least significant bit (LSB), where Input Digital Signal are (Do = 0001), (D1 = 0010), (D2 = 0100) and (D3 1000). While Digital Voltage is 5v. %3D %3D 80 kn De o R 40 kn 20 kn 20 kn Dz O 10 kn Vout(Da) Vout(D) = - Vout(o) -. Voutcb)
A multiplexer has 3 select lines and two enables. How many other inputs are there? How many TOTAL inputs are there? How many output/outputs are there? Draw a block diagram of this multiplexer.
Parts A ,B , and C. How is -89 represented using 8-bit two's compliment? (The answer should be 8 binary digits) Assume we are using the simple model for floating-point representation as given in the text (the representation uses a 14-bit format, 5 bits for the exponent with a bias of 15, a normalized mantissa of 8 bits, and a single sign bit for the number): Show how the computer would represent the numbers 100.0 using this floating-point format. Express the answer in hexadecimal using 4 hex digits. Suppose we are working with an error-correcting code that will allow all single-bit errors to be corrected for memory words of length 7. We have already calculated that we need 4 check bits, and the length of all code words will be 11. Code words are created according to the Hamming algorithm presented in the text. We now receive the following code word: 01111010101 Assuming even parity, according to our error-correcting code, in what bit is the error? Number the bits from the right…
1-Write microprocessor program using mnemonics to add two numbers 08 and 06. 2-Write the object code of the program. 3-Perform the program using STEP function. 4-Execute the program and write the results. Object code Mnemonics MOV AX A1 B0 MOV AL B3 MOV BL 04 ADD AL F4 HLT
digital system class