Question (2): Consider a BAC whose Q(1|0) = 0.2 and Q(0|1) 0.1. Suppose P[X =0] = 0.3. %3D Suppose the following DIY decoder is used. y Find: a) Draw the channel matrix. b) Channel matrix Q c) Joint pmf matrix P

Question (2): Consider a BAC whose Q(1|0) = 0.2 and Q(0|1) 0.1. Suppose P[X =0] = 0.3. %3D Suppose the following DIY decoder is used. y Find: a) Draw the channel matrix. b) Channel matrix Q c) Joint pmf matrix P

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted over M-level PCM system where the number of quantization levels is M = 16. The quantization distortion is specified not to exceed 1% of peak-to-peak analog signal. What would be the maximum number of bits per sample that should be used in this PCM system? What is the minimum sampling rate and what is the resulting bit transmission rate? i) ii)
3. Some GPS receivers use 1 bit ADCS (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.
Please assist with question 2 with details on how to do it. Thank you. 2. This problem addresses the digitization of a television signal using pulse-code modulation. The signal bandwidth is 4.5 MHz. Specifications of the modulator include the following: Sampling: 15% in excess of the Nyquist rate Quantization: uniform with 1024 levels Encoding: binary Determine (a) the Nyquist rate, and (b) the minimum permissible bit rate.
The information in an analog waveform, whose maximum frequency fm-D4000HZ, is to be transmitted using a 16-level PAM system. The quantization must not exceed +1% of the peak-to peak analog signal. (a) What is the minimum number of bits per sample or bits per PCM word that should be used in this system? (b) What is the minimum required sampling rate, and what is the resulting bit rate? (c) What is the 16-ary PAM symbol Transmission rate?
Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ±0.1% (full scale). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volts. Find the minimum sampling rate required. i) ii) Find minimum bit rate required in the PCM signal. Find the number of bits in each PCM word. iii) iv) Find the minimum absolute channel bandwidth required for the transmission of the PCM signal.
The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of : 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 43 Hz and an amplitude range of - 10 to 10 Vots. Determine the minimum bit rate fin bps) required in the PCM system? O a 688 O 774 O c 387 O d 86 Oe 258
The Transfer Fcn' block can be extracted from "Commonly Used Blocks' library. The 'Constant Source Block produces a constant signal with a default value of zero.
2. Some specific buses are usually used in system except () (2.0) A SPI bus 3. clock bus CUart bus D. USB bus 3. The relationship between the signal frequency fc and sampling rate Ts is () according to the Nyquist sampling law (2.0) A. fcTs>1 B、 2fcTs>1 C3fcTs>1 D. 4fcTs>1 4. The physical quantity signal can be analyzed in() (2.0) A、 time domain B. spatial domain Camplitude domain D、 length domain 5. ( ) sensor can be adopted to measuring structure minor damage. (2.0) A. Strain B、 Piezoelectric C、 Thermal resistance D. Thermocouple
Write TRUE if the statement is correct but if it’s false, change the underlined word or groupof words to make the whole statement correct. The subject is basic electronics. please answer my questions. thanks
Answer all questions below: 1. Draw the general block diagram of Frequency Division Multiplexing (FDM) 2. Multiplexing is a technique that allows the (simultaneous) transmission of multiple signals across a single data link. Figure Q2 below shows a multiplexer with four 500 kbps data stream inputs and 1 data stream output where the unit of data is 1 bit. Determine: i. ii. iii. 500 kbps The type of multiplexing technique used. The input bit duration. The output bit rate. 500 kbps 500 kbps. 500 kbps. ... ... ... 1 0 1 0 1 0 1 0 0000 1 1 1 1 0 1 0 0 MUX Figure Q2 Frames 0101 0001 110100010101
(7) An analog signal with a bandwidth of 4.2kHz is to be converted into binary PCM and transmitted over a channel. The peak signal to quantization ratio at the receiver output must be at least 55dB. (a) If we assume that Pg 0 and that %3D there is no ISI, what will be the word length and the number of quantization steps needed? (b) What will be the equivalent bit rate? (c) What will be the channel bandwidth required if rectangular pulse shapes are used?
See the figure below for Manchester scheme on CH-1 of Scope. Write the corresponding input bit stream. DE