**Question 2**Arrange the following molecules in increasing order of:**Molecules:**- **A:** CH₃CH₂OCH₂CH₃ (Ethyl ether)- **B:** CH₃CH₂CH₂OH (Propanol)- **C:** CH₃CH₂CH₂CH₃ (Butane)- **D:** (CH₃)₂CHOCH₃ (Isopropyl ether)- **E:** CH₃CH₂CH(CH₃)₂ (Isobutane)**Criteria:**a) **Boiling Points** *(top = lowest, bottom = highest)*- [ Select ]- [ Select ]- [ Select ]- [ Select ]- [ Select ]b) **Viscosity** *(top = lowest, bottom = highest)*- [ Select ]- [ Select ]- [ Select ]- [ Select ]- [ Select ]

-> Alcohols have high boiling point because alcohol can form intermolecular hydrogen bonds .…

Question 2 Arrange the following molecules in increasing order of: H₂C [Select] [ Select] [Select] [Select] [ Select] a) Boiling Points (top = lowest, bottom= highest) [Select] [Select] [Select] с [ Select] H3C [Select] H3C O ✪ ✪ O ✪ b) Viscosity (top = lowest, bottom= highest) ✪ O ✪ H3C CH3 ✪ CH3 CH3 D H₂ B OH H3C CH3 E

Question 2 Arrange the following molecules in increasing order of: H₂C [Select] [ Select] [Select] [Select] [ Select] a) Boiling Points (top = lowest, bottom= highest) [Select] [Select] [Select] с [ Select] H3C [Select] H3C O ✪ ✪ O ✪ b) Viscosity (top = lowest, bottom= highest) ✪ O ✪ H3C CH3 ✪ CH3 CH3 D H₂ B OH H3C CH3 E

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Look up the following solids' melting points and compare them: whey is the lrgest one large; wy is the smallest one small? dinitrogen N2 silicon Si potassium chloride KCl calcium Ca polyethylene (CH2)n
How do you solve this question?
Please do 4,5,6
Liquid X is known to have a lower vapor pressure and lower surface tension than Liquid Y. Use these facts to predict the result of each experiment in the table below, if you can. experiment 40.0 mL of Liquid X are put in one sealed 5 L flask, and 40.0 mL of Liquid Y are put in another sealed 5 L flask. The pressure in each fisk is slowly increased by pumping in argon gas. A 250 mL beaker is submerged in a large. container of Liquid X and turned upside down, and another 250 mL beaker is submerged and turned upside down in a large container of Liquid Y. Hydrogen (H₂) gas is bubbled into each upside-down beaker until 100 mL of liquid has been displaced. The masses my and my of hydrogen inside each beaker is then chemically determined. Note for advanced students: you may assume the solubility of H₂ in either liquid is very low. O predicted outcome Eventually both liquids boil, X first and then Y. Eventually both liquids boil, Y first and then X. Neither liquid will boil. It's impossible to…
What phase changes will take place when water is subjected to increasing pressure at a constant temperature of 0.0 °C? Pressure (kPa) 22,089 101 0.6 Ice (solid) A I D O deposition and condensation O freezing and deposition O boiling and freezing O deposition and melting T 1 Triple point B 0 0.01 Water (liquid) Water vapor (gas) 100 Temperature (°C) Critical point C I 374
Please don't provide handwriting solution
Study the following phase diagram of Substance X. A B C E- F temperature (K) A C If a sample of pure X is solid, in which region must the temperature and pressure be? G H A Which line must the temperature and pressure have crossed if a gaseous sample of X is observed to condense? H А В Which is the critical point of X? E O F G он O O OO O C ш о O O O OlO O O OO O O O pressure (atm)
Choose the answer which presents the chemical formulas for two substances in order of decreasing melting point (highest melting point first) and gives a valid reason for this order. a) Al > H2O due stronger dispersion forces in Al than in H2O. b) Xe > Ar because of the greater atomic mass and stronger dispersion forces of Xe. c) LiF > MgF2 due to lower atomic mass of Li+ than Mg2+. d) PbCl4 > PbO2 due to lower charge on Cl - than O2-. e) XeF4 > CF4 due dipole-dipole forces in XeF4 not present in CF4.
Choose the letter of the correct answer 1. What type(s) of intermolecular forces can exist C2H6 and BF3? A. Dipole-induced dipole B. Hydrogen bonding C. London dispersion D. Ionic bonding 2. Which of the following shows the increasing viscosity? A. CH4 < C6H14 < H2O < C3H8O3 B. C6H14 < CH4 < H2O < C3H8O3 C. C3H8O3 < H2O < C6H14 < CH4 D. C3H8O3 < C6H14 < H2O < CH4 3. Which of the following best describes the melting point of amorphous solid? A. Amorphous solids have definite melting points since they have a weak intermolecular force. B. Amorphous solids have definite melting points since they have a strong intermolecular force. C. Amorphous solids do not have a sharp melting points since they have a weak intermolecular force. D. Amorphous solids do not have a sharp melting point since they have a strong intermolecular forces.