Question 2 A 60mm diameter(d) shafts running at 3.351rads/sec and transmitting a torque of 2.9x10° N-mm i used to power a pulley for a conveyor via a key mechanism. A factor of safety of 4 is required due to the nature of the application. The width of the key (w) is 0.3d and the thickness of the key (t) i: 0.1833d. a. Determine all the dimensions of the key. b. Determine the power transmitted via the key. Shear stress 320MPa Compressive stress 380MPa Tensile stress 420MPa

Question 2 A 60mm diameter(d) shafts running at 3.351rads/sec and transmitting a torque of 2.9x10° N-mm i used to power a pulley for a conveyor via a key mechanism. A factor of safety of 4 is required due to the nature of the application. The width of the key (w) is 0.3d and the thickness of the key (t) i: 0.1833d. a. Determine all the dimensions of the key. b. Determine the power transmitted via the key. Shear stress 320MPa Compressive stress 380MPa Tensile stress 420MPa

Essentials of Business Analytics (MindTap Course List)

2nd Edition

ISBN:9781305627734

Author:Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Publisher:Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Chapter5: Probability: An Introduction To Modeling Uncertainty

Section: Chapter Questions

Problem 33P: Suppose that Motorola uses the normal distribution to determine the probability of defects and the...

See similar textbooks

Similar questions

typing clear no chatgpt used i will give 5 upvotes
I need typing clear urjent no chatgpt used i will give 5 upvotes pls full explain
A spring with a 4 kg mass is resting on a horizontal frictionless table and is attached to a wall at the left end. It will stretch 0.5 m beyond its natura length when a force of 14 N is applied. If the spring begins at the equilibrium position and is pushed to the right with an initial velocity of 2 m/s, fin the position of the mass after t seconds. (Assume that movement to the right is the positive x direction.) x(e) 0.756 sin(2.6461) × Graph the position function of the mass. Χ x
5.6.2AW14 x 109 beam of A 992 steel with lateral support at 10-foot intervals. Assume Cb = 1.0 and determine the nominal flexural strength
The figure below shows a 114-turn square coil rotating about a vertical axis at at -1,770 rev/min. The length of a side of the coil is 20.0 cm. The horizontal component of the Earth's magnetic field at the coil's location is equal to 2.00 x 10-5 T. 20.0 cm 20.0 cm (a) What is the magnitude of the maximum emf (in mV) induced in the coil by the Earth's magnetic field? mV (b) What is the orientation of the coil with respect to the magnetic field when the maximum emf occurs? O The plane of the coil is parallel to the magnetic field. The plane of the coil is perpendicular to the magnetic field. ○ The plane of the coil is oriented 45° with respect to the magnetic field.
I need typing clear urjent no chatgpt used i will give 5 upvotes pls full explain
1. The projection of the liquidus surface of the ternary system A-B-C is given below; a) Draw the isothermal sections at 400°C and room temperature. (20p.) b) For composition X, what is the amount and composition of solid phase at its solidus temperature? What would you suggest to increase its amount by keeping temperature constant? (20p.) A (705°) B (924°) A.B 569° 547° 850 650- X 550- 513 $450 460° 550 500 484° 400° 500- 550- -650- 600- 750- Yo A3B2C 2B.C 736° 683° B.C wt.% 660° A3C 580° A6C (684°)
3. Reflection and Refraction (25%): A gold coin lies at the bottom of a clear pond under 5.0 m (meters) of water, and 3.5 m (meters), horizontally, from the shore (wall). Assume the pond has vertical sides, or walls. If a light beam is incident on the water surface at the wall, at what angle, 8 (Theta), relative to the wall, must the beam be directed so that it will illuminate the coin? Pond Surface Ө Light Source (Sun) Gold Coin 5 m 3.5 m
15. A power generator produces 2.00 kA of current at 500 V. Electric power must be transmitted with 1.00% loss in transmission lines of 95.00 total resistance. To achieve this, the voltage is stepped up by a transformer with 32 turns in its primary coil. a. How much voltage is carried by the transmission lines? b. How many turns are in the transformer's secondary coil?
A 1.4-kg decoration hangs from the three wires as shown in the figure. The wire on the left makes an angle ax = 66.5° with the ceiling. The wire on the right makes an angle B-37.11° with the ceiling. The wire on the left has a tension that is twice that of the tension in the wire on the right. Part A What is the tension in the vertical wire attached to the decoration? This value is used in the next part, so use 4 significant digits. FT Value Submit Request Answer Part B ? Units a B
Read the question carefully and give me right solution according to the question
The production department is proposing the purchase of an automatic insertion machine. It has identified three machines and has asked the accountant to analyze them to determine which one has the best average rate of return. Machine A $43,529.50 $80,697.00 Machine B Machine C $64,675.95 310,925.00 268,990.00 431,173.00 Estimated average income Average investment Oa. Machine B Ob. Machine A Oc. Machine C Od. Machines B and C have the same preferred average rate of return.