Question 17 A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross- sectional area of the rod is 50 mm². Neglect the size of the couplings at B, C and D. Calculate the displacement of the rod at D when F₁ = 3.0 kN, F₂ = 4.6 kN and F3 = 8.2 kN. Input your answer as a value only in mm to two decimal places without +/- sign. -1m-1.5 m -1.25 m AF, B C F₂ DF₂

Question 17 A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross- sectional area of the rod is 50 mm². Neglect the size of the couplings at B, C and D. Calculate the displacement of the rod at D when F₁ = 3.0 kN, F₂ = 4.6 kN and F3 = 8.2 kN. Input your answer as a value only in mm to two decimal places without +/- sign. -1m-1.5 m -1.25 m AF, B C F₂ DF₂

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the figure. The cross-sectional area of the rod is 50 mm2. Neglect the size of the couplings at B, C and D. Calculate the displacement of the rod at D when F₁ = 2.8 kN, F2 = 4.3 kN and F3 = 7.3 kN. Input your answer as a value only in mm to two decimal places without +/- sign. 1 m 1.5 m-1.25 m- C F₂ A F₁ B D F3
The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at point E as in the figure and is subjected to a force of 800 N, a torque of 45 N.m and a moment of 300 N.m I applied from the other end of the pipe as in the figure, it will form at point A; (a) Principal planes (Ɵ1, Ɵ2). (b) Prime requirements (σmax,σmin), (c) their principal planes,
3. A force P is applied to the rigid lever arm ABC as shown. The arm rotates counterclockwise about pin A through an angle of 0.06°. Calculate the normal strain developed in wire BD. Answer: EnD = 0.0014 mm/ mm 300 mm B 400 mm
Question 3 T/2 A 1200 Nm A homogeneous steel shaft (G=83GPA) loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member AB. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
A beam is constructed from three wooden boards, as shown in the figure. Thetorque of 1250 Nm is applied at an angle of 35º to the vertical, determine: the location and magnitude of the maximum stresses on the beam and the location of the neutral axis .
A uniformly tapered aluminum-alloy tube AB of circular cross section and length L is shown in the figure. The outside diameters at the ends are da and dB = 2d4. A hollow section of length and constant thickness t = A is cast into the tube and extends from B halfway toward A. t constant de- 21 B dg (a) dg (b) (a) Find the angle of twist of the tube when it is subjected to torques T acting at the ends. Use numerical values as follows: da = 2.8 in., L = 43 in., G = 3.5 × 10° psi, and T = 38,000 in. – lb. Round your answer to two decimal places. ФА (b) Repeat (a) if the hollow section has constant diameter da (see figure part b). Round your answer to two decimal places.
None
Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 18 degree Celsius, 2 m- - 2 m A 2 m C Use E = 200 GPa, linear of coefficient expansion = 11 7x 10 per degree celsius and A = 4500 mm2 Compute for the deformation of the right rod in mm. Select the correct response 0.0468 mm 0.117 mm 0 0234 mm 0.0842 mm
. Consider the following wooden T-beam on its side. It consists of two wooden parts glued together. Assume the glue nas a perfect bond. The densities of the two wooden parts differ and are indicated on the figure. The figure is not to scale. y Pq = 900 kg/m %3D 17 mm P2 = 740 kg/m? 20 mm 150 тm Determine the a-coordinate I of the center of mass of the T-beam. 90 mm
Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 106mm Load = 2 kN A 5m B Using the following method: 2 KN + 2m + 2m |- You are tasked to analyze the continuous beam by calculating the: > the displacement on the beam at B and C and > the reaction at the supports Matrix Structural Analysis Use the following steps as a guide to analyze the beam: Matrix Structural Analysis ✓ Produce Notations ✓ Establish the known displacements and known external load ✓ Produce Member Stiffness Matrix ✓ Displacement and Load ✓ Calculating the displacement Calculating the reaction at the support
The piece of plastic is originally rectangular. Suppose that a = 300 mm and b = 450 mm. A) Determine the shear strain γxy at corner C if the plastic distorts as shown by the dashed lines.
The circular shaft AB consists of a 19 mm diameter solid steel cylinder in which a 5 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 59 Nm. What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal place without +/- sign. L₁ L₂ C 150 Nm B