Question 1. The shaping machine is used to machine flat metal surfaces especially where a large amount of metal has to be removed. The shaper machine is a reciprocating type of machine basically used for producing the horizontal, vertical or flat surfaces. The shaper holds the single point cutting tool in ram and workpiece is fixed in the table. A shaper mechanism is designed to give a slow cutting stroke and a quick return to a blade attached to the slider at C. Determine the velocity of the slider block C at the instant 0= 60°, if link AB is rotating at 4 rad/s. 125 mm C 45 B WAR =4 rad/s 300 mm

Question 1. The shaping machine is used to machine flat metal surfaces especially where a large amount of metal has to be removed. The shaper machine is a reciprocating type of machine basically used for producing the horizontal, vertical or flat surfaces. The shaper holds the single point cutting tool in ram and workpiece is fixed in the table. A shaper mechanism is designed to give a slow cutting stroke and a quick return to a blade attached to the slider at C. Determine the velocity of the slider block C at the instant 0= 60°, if link AB is rotating at 4 rad/s. 125 mm C 45 B WAR =4 rad/s 300 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

35
A cylinder of 155 mm diameter is to be reduced to 150 mm diameter in one turning cut with a feed of 0.15 mm/rev and a cutting speed of 150 m/min on a NC lathe. What are the programmed feed rate and the material removal rate
11. In the following operation the axis of the tool is perpendicular to feed direction: * Slotting All choices Picket milling Slab milling T
Using slot milling with a cutting tool surface width of 36mm was performed from the top surface to cut a workpiece of 85 x 42 x 8 cm into two equal parts. The milling cutter is 180 mm in diameter and has eight teeth. Cutting speed = 60 m/min, chip load = 0.35 mm/ tooth, and depth of cut = 2 mm, given that the setup and machine settings provide an approach distance of 7mm before actual cutting begins and an overtravel distance of 20 mm after actual cutting has finished, and the return time is a 4-second for idle pass stroke. Determine:- 1. What is the total machining time required for the entire workpiece? 2. The maximum metal removal rate during cutting.
Problem #2: Do a comparison between turning Vs. milling operations use some graphs if possible.
Question 19 Which of the following machine tools is the most suitable one for machining of relatively large batches with several operations? Answers: a. Toolroom lathe b. Turret lathe c. Vertical turret lathe d. Engine lathe e. Speed lathe Consider the following statements on milling machines 1. 2. Facing cutters have a tapered or straight shanks End mills usually are bolted at the end of a stub arbor 3 Plain milling cutters are used for profilling as well Answers: a. Only 2 and 3 are correct b. Only 1 and 2 are correct c. Only 1 and 3 are conect d. None of them is correct e Only 1 is correct Question 21 Find the incorrect statement about center type cylindrical grinding. (If you cannot find an incorrect statement among items a, b, c and d then code "e" for this question) Answers: & Workpiece rotates b. Grinding wheel rotates Usually workpiece traverses d, Depth of cut is usually determined by infeed of the grinding wheel e. All are correct Consider the following statements about…
In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as longitudinal feed parallel feed cross feed taper feed
Identify the type of milling operation in which the several surfaces of the the workpiece is machined simultaneously. slot milling angular milling gang milling side milling
Fill in the blanks.(Manufacturing) Thanks in advance