QUESTION 1When discussing motors with commutators and brushes, the neutral plane is:perpendicular to the magnetic field of the magnets, and alignment of the brushes should be along the neutral plane in order to minimizecommutator sparkingthe conductor that allows current to return back to the source.the plane resulting in the maximum number of magnetic lines that will be cut when the motor is in rotation.parallel to the magnetic field of the magnets, and alignment of the brushes should be perpendicular to the neutral plane in order tominimize commutator sparking

Four options are given in the question. We need to choose the correct option. It is asked when…

QUESTION 1 When discussing motors with commutators and brushes, the neutral plane is: O perpendicular to the magnetic field of the magnets, and alignment of the brushes should be along the neutral plane in order to minimize commutator sparking O the conductor that allows current to return back to the source. O the plane resulting in the maximum number of magnetic lines that will be cut when the motor is in rotation. O parallel to the magnetic field of the magnets, and alignment of the brushes should be perpendicular to the neutral plane in order to minimize commutator sparking

QUESTION 1 When discussing motors with commutators and brushes, the neutral plane is: O perpendicular to the magnetic field of the magnets, and alignment of the brushes should be along the neutral plane in order to minimize commutator sparking O the conductor that allows current to return back to the source. O the plane resulting in the maximum number of magnetic lines that will be cut when the motor is in rotation. O parallel to the magnetic field of the magnets, and alignment of the brushes should be perpendicular to the neutral plane in order to minimize commutator sparking

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

current - 1=?, and the power factor - cosp =?. 4. An out of balance three phase star connected load has the following complex currents: I₁ = lejº,A, I₂ =le¯6⁰,A and I₁=1e¹j6⁰, A. This load is supplied by a four wire power line from a balance voltage source. Find the r.m.s. value of the neutral current Io =? Wait to th
Q2)A train is driven by a DC machine with independent electrical excitation. At a speed of 1500 rpm, the following magnetization characteristic has been measured. Ea(V) If(A) 1- Sketch the equivalent circuit of the DC machine. 2- Why is a voltage induced in the armature when the excitation current is zero? 3- Why does the induced voltage at high excitation currents not increase proportional to the excitation 60 430 790 960 1130 1190 1270 6. 10 12 14.8 16.4 30.8 current? 4- Sketch a power electronic converter that can be used to control the voltage on the machine terminals.
Q 4. An 8-pole DC generator has 400 armature conductors and a useful flux of 0.05 Wb. What will be the emf generated if it is lap wound and runs at 1,500 rpm? What must be the speed at which it is to be driven to induce the same voltage if it is wave wound? (Ans. 500 V; 375 rpm) 05 A vave wound armature generator has 51 slots Fach slot contains 20 conductors The
QUESTION # 01 The armature winding of a DC motor has 360 conductors, of which only 80% lie directly under the pole, where the flux density B = 1.1 T. The armature diameter is 30 cm and its length is 20 cm. The conductor current is 16 A. Determine: a) The total force created by the conductor. b) The shaft torque developed.
A 4 pole d.c. motor takes a 38.6 A armature current. The armature has lap connected 350 conductors. The flux per pole is 15 mWb. Calculate the gross torque developed by the armature of the motor. Also calculate Torque if flux per pole changes to 18 mWb and state difference in torque from 18 mWb to 15 mWb
Which one of the following is not the function of pole shoes in a dc machine? (1) To reduce eddy current loss (2)To support the field coils (3)To spread out flux for better uniformity (4)To reduce the reluctance of the magnetic path (5)None of the above.
A motor can have different torque characteristics depending on the resistance of the rotor bars and the inductive reactance of the rotor. With this in mind, which of the following is a true statement? A - The resultant flux density in the air gap between the rotor and the stator approaches zero as torque increases. B - As the motor speeds up, inductance is increased because slip and the frequency of the induced EMF is improved. C - The phase angle of the rotor affects the amount of induced current that flows in the rotor and the impedance between the rotor current and induced voltage. D - The impedance of the rotor affects the amount of induced current that flows in the rotor and the phase angle between the rotor current and induced voltage.
Please write text, not handwriting
State two reasons why a self-excited shunt dc generator may fail to build up a voltage. In each (both) case, briefly explain what can be done to correct the problem. Reason #1 Solution #1 Reason #2 Solution #2
Q4. An 8-pole DC generator has 400 armature conductors and a useful flux of 0.05 Wb. What will be the emf generated if it is lap wound and runs at 1,500 rpm? What must be the speed at which it is to be driven to induce the same voltage if it is wave wound? (Ans. 500 V; 375 rpm) O of a 6 pola proto hon 51 clots Fagh ing 20 du