Question 1: For the circuit below, the Zener diode has Vzo = 5 V, Vz = 5.1 V and rz = 20 N. Consider R1 = 1 k. a- Check if the Zener diode in this circuit is ON or OFF. Explain b- Calculate the current Iz. c- Calculate the resistance R1. d- Calculate the power consumed by the Zener diode. Vs +. V1 - Vo 20 V

Question 1: For the circuit below, the Zener diode has Vzo = 5 V, Vz = 5.1 V and rz = 20 N. Consider R1 = 1 k. a- Check if the Zener diode in this circuit is ON or OFF. Explain b- Calculate the current Iz. c- Calculate the resistance R1. d- Calculate the power consumed by the Zener diode. Vs +. V1 - Vo 20 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a) Name of the Circuit? (Assume Silicon Diodes) , 4:1 D b) Find the peak input voltage to the 120 V rms diodes. R 1.0 k D2 c) Find the average output voltage? d) Find the DC current? d) Find the Peak Inverse Voltage of the diodes? e) Draw the output waveform. eetee
If the positive cycle of the waveform for full wave bridge rectifier , Which of the diodes is working . ..... ...... 10:1 120 V ms Output 60 Hz Puec) RL 220 N Dz 1000µF O D1, D2 D3, D2 D4, D2 D1, D4 not all above D1, D3 ellee
5. The bridge rectifier shown in Figure 2 uses ideal diodes. The input voltage is 24V. Find: DC output voltage b. Sketch the output waveform a. D2 D3 R1 = 12 k2 %3D DA Figure 2. Circuit for problem 5 and 6 ell ll
Ce301 q5
In this Zener diode regulator, the source voltage varies from 6 V to 11 V. Assume that the load current varies between 2 mA and 48 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Please answer in typing format solution please only typing format solution please
Since R1=4.51 Kohm, R2=1.19 Kohm R3=2.74Kohm R4=5.60Kohm VCC=23.00V and diode silicon in the circuit given in the figure, find the current passing through the diode in mA
5. The bridge rectifier shown in Figure 2 uses ideal diodes. The input voltage is 24V. Find: a. DC output voltage b. Sketch the output waveform D2 D3 R1 = 12 k2 Da D Figure 2. Circuit for problem 5 and 6 6. If the bridge rectifier shown in Figure 2 is modified using silicon diodes, find: a. dc output voltage b. sketch the output waveform ell ll
Consider the diode circuit shown below. If in the given circuit, Vs is replaced by a 12V battery and diodes D1 & D2 are considered ideal, what is the potential Vout equal to?
QUESTION 2 With the aid of lo-VD graph, briefly describe the behavior of silicon diode and ideal diode in ON state condition. a) b) Figure Q2b represents a voltage regulator circuit. Determine R and V₂ value to maintain V₁ at 10V for a load variation, I, from OmA to 200mA. Then calculate Pzmax for the zener diode. 20V IR R 20 ww Iz Vz Figure Q2b RL
circuit given in Figure 3 use Complete Diode Model and find the voltage across R1 and R2 and total current flowing in this circuit. Given that diode forward resistance is 15 Ohms for D1 and 10 Ohms for D2, also reverse current flowing acrossD2 is 20 micro Amperes.
I don't know what will be the figure of example 2. Please help. Thank you.
2. For the following figure 1 employing the diode characteristics of figure 2. Determine a) DC load line b) Voltage across the resistance c) Instead of the DC source use a 10V AC source and find the AC load line. D1 charteritien DIN4002 V1 10V R1 2k R2 2k HINA Bever charateri -1A) Junetion diode characteristies, Ge and S Figure 1 Figure 2