QUESTION 1 A nozzle is advice for increasing the velocity of a steadily flowing fluid. At inlet to a certain nozzle the specific enthalpy of the fluid is 3025kJ/kg and the velocity is 60m/s. At exit from the nozzle the specific enthalpy is 2790kJ/kg. The nozzle is horizontal and there is a negligible heat loss from it. Calculate: 1.1 the velocity of the fluid at exit;

QUESTION 1 A nozzle is advice for increasing the velocity of a steadily flowing fluid. At inlet to a certain nozzle the specific enthalpy of the fluid is 3025kJ/kg and the velocity is 60m/s. At exit from the nozzle the specific enthalpy is 2790kJ/kg. The nozzle is horizontal and there is a negligible heat loss from it. Calculate: 1.1 the velocity of the fluid at exit;

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

Question Four Air flows steadily adiabatically through a pipe with a cross-sectional of 0.002 m?. At the inlet of the duct, the pressure and temperature are 100 kPa and 50°C, respectively. At the exit of the duct, the temperature and velocity are 100°C and 600 m/s, respectively. Determine the Mach number and the velocity at the inlet section. Also, calculate the mass flow rate. Ans. M 1.884, vi = 678.7 m/s, m = 1.46 kg/s.
-NES Start from first principle to show that, for perfect gas the velocity of the sound is given by: C= √KRT
How much air is used per kg of coal burnt in a boiler having a chimney of 31.1 m height to create a draught of 19 mm of the water column when the temperature of the flue gases in the chimney is 361 o C and the temperature of the boiler house is 28.4 o C. Also find the equivalent gas head of the chimney.
Steam expands adiabatically in a nozzle from inlet conditions of 130(psia), 420(°F),and a velocity of 230(ft)(s)−1 to a discharge pressure of 35(psia) where its velocity is2000(ft)(s)−1. What is the state of the steam at the nozzle exit, and what is SG for theprocess?
In a heat engine, water vapor flows into a turbine and then it enters a condenser for rejecting thermal energy. The system requires maintaining the gauge pressure of the steam at 1400 kPa at the turbine inlet and at a vacuum of 71 cmHg in the condenser. Having that the barometric pressure is measured as 77.2 cmHg, calculate the absolute pressures (in kPa) of the steam at the turbine inlet and in the condenser. (Density of mercury is 13600 kg/m3)
Detailed Steps
A compressed air tank in a service station has a volume of 10 ft³. It contains air at 70°F and 150 psi (abs.). How many tubeless tires can it fill to 44.7 psi (abs.) at 70°F if each tire has a volume of 2.0 ft3 and the compressed air tank is not refilled? The tank air temperature remains constant at 70°F because of heat transfer through the tank's large surface area. N = 16.77
Water with a specific heat of 1 BTU/lbmoF is pumped using a 1-hp jet pump from a well that is 20 ft deep into a vented water vessel 160 ft above the ground. In the process, 400 BTU/min of heat is lost from the system. What is the temperature (oF) of the water as it enters the vessel if the flow rate of the water is 5 gal/min? Assume the temperature of water in the well is (35oF).
Use steam table, Saturated steam has a pressure of 2.546 Mpa. What are the temperature, specificinternal energy, specific volume, and specific entropy? Is the condition of the steamis wet, dry or superheated? Why?
The minimum fresh air requirement of a residential building is specified to be 0.35 air change per hour (per ASHRAE standards). That is, 35% of the entire quantity of air contained in a residence should be replaced by fresh outdoor air every hour. The ventilation requirement of a 3-meter highresidence with 150 square meters of floor space is to be met by air provided by a single fan.a. Determine the required flow capacity of the fan (in m3/min).b. Find the diameter of the fan duct required (circular cross-section) if the average air velocity from the duct is to be 3 m/sec.
Design a hydrocooling unit to cool down fruits and vegetables from 30 °C to 5 °C in 20 minutes at a rate of 20,000 kg of fruit or vegetables/h. The design must fulfill the following requirements: The unit will be an immersion flooded system. It must be able to cool down and transport the products in chill water. The tank has the following dimensions approximate. three meters wide and up to 90 cm hight. The water will circulate and be cooled through the evaporation section of a refrigeration system. The refrigerant temperature inside the coils will be -2 °C, and the water temperature must not drop below 1 °C and must not exceed 6 °C. Assuming reasonable values for the average density, specific heat, and porosity of the product (the fraction of the volume of air in a box), recommend reasonable values for: The speed of the water through the canal, the capacity of the cooling system. the compressor power.
Help me solve this one, rush