Question 07) Design a sequential circuit with two JK flip-flops, A and B and two inputs E and F. If E = 0, the circuit remains in the same state regardless of the value of F. When E = 1 and F = 1, the circuit goes through the state transitions from 00 to 01, to 10, to 11, back to 00, and repeats. When E = 1 and F = 0, the circuit goes through the state transitions from 00 to 11, to 10, to 01, back to 00, and repeats. (12 Marks + 5 Marks for presentation) [CLO 2; PLO 3; C3]

Question 07) Design a sequential circuit with two JK flip-flops, A and B and two inputs E and F. If E = 0, the circuit remains in the same state regardless of the value of F. When E = 1 and F = 1, the circuit goes through the state transitions from 00 to 01, to 10, to 11, back to 00, and repeats. When E = 1 and F = 0, the circuit goes through the state transitions from 00 to 11, to 10, to 01, back to 00, and repeats. (12 Marks + 5 Marks for presentation) [CLO 2; PLO 3; C3]

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

1. Given the following circuit: 5 ns D. 1ons The gate delays are as shown above the gates. A, B, C are three input, and all of them are varying, as given below: A = 0 at time 0, and stays constant until time = 20 ns, when it changes to 1 and stays constant there after B = 1 at time = 0, and stays at 1 value until time = 35 ns, and then changes to 0 at35 ns, and stays constant after that. !3! %3D C= 0 at time 0 and changes to 1 at 50ns Plot A, B, C upto time = 70 ns.
2
Q9
Q2: For the circuit shown in below, use (matlab, c++, or python) and Nodal Analysis to: a) Find the voltage across the current source 11 terminals b) Find the current through the resistance R1 c) Find the real and reactive Powers delivered by the current source 11 Find the real and reactive Powers consumed by the capacitor C2 d) 11 10 A RMS 50 Hz +35 Deg Z1 AM R2 402 Z4 R4 80 m Z2 L2 15 mH 12 7A RMS 50 Hz +74 Deg Zc1 C1 150 F R3 30 www w R6 40 Z6 L3 25 mH E1 100 V RMS - 40 Deg Z5 50 Hz www R5 20 Zc2 C2 200 F
• Design a sequential circuit with two T Flip Flops, A and B, and two inputs, E and x. If E=0, the circuit remains in the same state regardless of the value of x. When E=1 and x=1, the circuit goes through the state transitions from 00 to 01 to 10 to 11 back to 00, and repeats. When E=1 and x=0, the circuit goes through the state transition from 00 to 11 to 10 to 01 back to 00, and repeats
Use the following state diagram and create the state table for a synchronous to detect the sequence. The circuit has a single input, x, and a single output z. The output is logic-1 whenever the input sequence 1001 is detected, logic-0 otherwise. Note that overlapping sequences are allowed, Create the initial state table, and the complete state table. Write the equations for all the state variables and the output z.
= 1 causes the heater to decrease its Q3: A Moore sequential circuit has three inputs (X2, X1, and Xo) that specify a temperature range in a room. The circuit has two outputs (I and D) that control a heater for the room; I = 1 causes the heater to increase its heat output, and D heat output. If the temperature range is 0, 1, or 2 for three successive clock cycles, the circuit generates I = 1, and conversely if the temperature range is 5, 6, or 7 for three successive clock cycles, the circuit generates D = 1; otherwise, I = 0 and D = 0. 1. Draw a state diagram. 2. Construct a state table. 3. Using D flip-flops, construct a state assigned table. 4. Determine the next-state and output logic expressions. 5. Sketch the corresponding logic circuit.
b) Given a sequential circuit in Figure Q4b. Determine the next state equations, state table, state diagram, function that the circuit perform and revise the circuit by using T Flip Flops. SET SET Q K CLR Q K CLR Q CLK Figure Q4b
Design the transition logic using One FF per state method for the following state diagram, use logic states for the condition signals- T2 T3 C= 1 C= 0 A, = 0 To A, = 1
3. Design a combinational circuit with three inputs and one output. Follow the steps in designing a combinational circuit and show your solution. a. The output is 1 when the binary value of the inputs is less than 3. The output is 0 otherwise. b. The output is 1 when the binary value of the inputs is an even number.
Q2. Design a sequential circuit with two JK flip-flops A and B and two inputs E and x. If E=0, the circuit remains in the same state regardless of the value of x. When E=1 and x=1, the circuit goes through the state transitions from 00 to 01 to 10 to 11 back to 00 and repeat. When E=1 and x=0, the circuit goes through the state transitions from 00 to 11 to 10 to 01 back to 00 and repeat.
1- In the following sequential circuit. There are 2 D FF (A and B), 2 inputs (x and y), and 1 output z The output and next-states equations are given A(t+1) = x'y + xA B(t+1) = x'B + xA z=B b- List the state table for the sequential circuit.