Que. A rectangular channel 2.0 m wide has a discharge of 250 litres per second, which is measured by a right-angled V- notch weir. Find the position of the apex of the notch from the bed of the channel if maximum depth of water in the channel is not to exceed 1.3m. Take Cd = 0.62.

Que. A rectangular channel 2.0 m wide has a discharge of 250 litres per second, which is measured by a right-angled V- notch weir. Find the position of the apex of the notch from the bed of the channel if maximum depth of water in the channel is not to exceed 1.3m. Take Cd = 0.62.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please answer it neat and clean hehe, thank you
Urgent
Problem A rectangular channel 2.0 m wide has a discharge of 250 litres per second, which is measured by a right-angled V-notch weir. Find the position of the apex of the notch from the bed of the channel if maximum depth of water is not to exceed 1.3 m. Take C¿ = 0.62.
A triangular shaped channel having a slope of 0.0001with a depth of 1.215 m..It is made of timber with n=0.012.Calculate the discharge of the channel using the best hydraulic or the most economical triangular section Select one: O a. 0.4371 cu m/s O b. 0.6982 cu m/s O c. 0.5892 cu m/s d. 0.6434 cu m/s O e. 0.3092 cu m/s
A. Design a trapezoidal channel to carry a discharge of 10.5 m^3/s. The bottom slop of the channel is 0.0035. Also the flow depth is half of the channel bottom width. Take roughness coefficient as 0.025 and side slop as 1H to 4V. B. Based on the given information and your results in part A, compute the state of flow
6. A 3.6 m wide rectangular channel carries water to a depth of 1.8 m. In order to measure the discharge, the channel width is reduces to 2.4 m and a hump of 0.30 m height is provided in the bottom. Calculate the discharge if water surface in the contracted section IQ-6.418 m/s] drops by 0.15 m. Assume no losses.
Compute the discharge in m3/s of a triangular weir, C = 0.60, e = 90 deg, H= 2.2m O 7.106 O 10.176 O 5.174 O 14.175
Question-05:A trapezoidal notch having bottom width of 1.0 m is installed in a 2.0 m X 2.0 m rectangular channel. Solve fordischarge through the notch in cubic meter per minute if the depth of water flowing in the notch is 1.5 m. Takethe coefficient of discharge for the notch as 0.64.
Q. No 1). Determine the discharge through a trapezoidal channel having X m base width, Side slope is 2:1 (Vertical to Horizontal). If the height of free surface of the water above the bed is 4 m. The bed slope is 1 in 1500, take n= 0.012. Width X=85 Q. No 2). A pipe line is designed to supplying water with flowrate of X 1/s to fulfil the demand and consumption of a city. Determine the head loss and velocity of flow in 1500 m long water supply line section having diameter of Y cm. Assuming coefficient of friction factor f= 0.00155. X (Flowrate)= 88 Y (Diameter)= 21.6 Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine velocity of water when it reach to a location 1.3 km from the pumping station where maximum head loss was found to be X m. Assume that pipe used is having diameter of Y cm and commercial steel pipe is used in the project. X(Headloss,m) =2, Y (Dia, cm) = 169 Q. No 4). A rectangular channel of X ft width is supplying water at…
Que 102. Determine the maximum discharge for a broad crested weir of length 60m, and height of water 60cm above its crest. Assume Ca= 0.62
Determine the vertex angle (in deg.) of a V-notch weir for a discharge of 29,762 L/s and a head of 4.49 m. Use Cd = 0.942. Round off to two decimal places.
QUESTION 8 The discharge over a trapezoidal weir is 1.315 cu.m/s. The crest's length is 2m and the sides are inclined at 75 degrees 57 minutes 50 seconds with the horizontal. Find the head over the weir in meter. USE 1 DECIMAL PLACES.