quarter scale turbine model is tested under a head of 36 m. The full scale turbine is required to work under o head of 100 m and to run at 428 rpm. At what speed must the model be run and if it develops 135 HP and uses 0'324 m3/ sec of water at this speed, what power will be obtained from the full scale turbine assuming that its efficiency is 3 per cent better than that of the model?

quarter scale turbine model is tested under a head of 36 m. The full scale turbine is required to work under o head of 100 m and to run at 428 rpm. At what speed must the model be run and if it develops 135 HP and uses 0'324 m3/ sec of water at this speed, what power will be obtained from the full scale turbine assuming that its efficiency is 3 per cent better than that of the model?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A petrol engine has mechanical efficiency 0.8 and lower calorific value of 44.2 MJ / kg. The engine bore 0.06 m and stroke of 0.08 m. The engine speed of 2000 rpm. The consumption of fuel about 8 liter / h and the brake weight is 200 N. Take the density of fuel as 750 kg / m3 and torque arm of 400 mm.Find the specific fuel consumption. *
Problem 1(5): A centrifugal pump transports water between two reservoirs. The pump has an outer diameter of 15 cm, an inner diameter of 8 cm, and a blade width of 2 cm and operates at 1750 rpm. If the water enters the pump axially at ẞ₁ = 45º¸ compute the volume flow rate, Problem 2(10): In the pump of problem 1, the water exits at B₂ 65° when the pump is driven at 1750 rpm. = Compute the minimum power required by the pump?
A jet engine is bolted to a stationary test stand and run at full thrust. Air enters the engine at a rate of 80 Ibm/sec and fuel enters the engine at a rate of 0.8 lbm/sec. Additionally, the following values are known: Pinlet = 13 psi Vinlet = 500 ft/sec Ainlet = 4 ft2 NO exhaust = 14.7 psi exhaust = 3 ft Find the reaction force required to hold the engine in place on the test stand. NOT UPOA OT UP Aexhaust = DO NOT DO NOT UP UPLOAD TO OAD TO CHu OT UPL
Can someone please help me to solve the following question showing all work. R-in = 5cm R-out = 15cm
Solve it on priority and correctly
A fan delivers 5.226 m^3/sec at a static pressure of 6.895 cm of water when operating at a speed of 450.941 rpm. The power input required is 3.97 kW. If 9.15 m^3/s are desired in the same fan and installation, find the pressure in cm of water
A two-blade wind turbine is installed on top of a hill experiencing winds of up to 80 mile/h. Downstream of the propeller the wind speed is 50 mile/h. Assume ideal gas and standard condition for air and find the tip to tip diameter of the propeller to obtain a theoretical efficiency of 50%.
explanation of the performance tests undertaken for a wind turbine. With the options found, give a justified recommendation for the best system.
Calculate the blade length of a wind turbine rotor which produces a maximum power of 4 MW at a wind speed of 41 Km/Hr. Use air density as 1.23 Kg/m³, generator efficiency as 93%, gear box efficiency as 0.74 and power coefficient of blades as 0.38.
Analyze to select the type of the turbine when its diameter is 600 mm, rotational speed is 600 rpm and working under a water head of 120 meters. The buckets deflect the 100 mm diameter jet through an angle of 165°. Take the coefficient of velocity for the nozzle as 0.97. Use Table given below for selection of turbine. Sr. # Specific speed (rpm) Type of turbine 1 8-30 Pelton wheel with one nozzle 30 - 50 Pelton wheel with 2 or more nozzles 50-250 Francis turbine 4 250-1000 Kaplan turbine 2. 3.
Provide the diagram for the problem. Choose the correct answer and provide complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. A. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? a. 86%b. 65%c. 77%d. 50% B. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe. a. 45 lb/sb. 37 lb/sc. 52 lb/sd. 29 lb/s
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.