QS-2: For the given system below calculate the displacement of the point D? Esteel: 210 GPa, Ealiminium: 70 GPa 50mm 50mm A 10kN B с çelik 100mm 24KN alüminyum A₁=400mm² 12kN A₂=200mm²

Q: The simply supported beam in Figure below has a rectangular 3kN w = 1.5 kN/m cross section 100 mm…

A: Finding out maximum stress.

Q: Q2: Locate the center of mass(X,Y) for the Frame assembly (shown in Fig. Down) if each of the three…

A:

Q: 5. A metallic top-hat stringer reinforced wing skin (function of the material A=150) has a width of…

A: The function of the material = 150Width =1.5 mUnsupported length =0.5 mApplied compressive load =120…

Q: A 1.5 m long column has a circular cross-section of 50 mm diameter. Consider Rankine's formula 1 for…

A: Given-1.5 m long column,Diameter of cross-section d=50 mm,Stress fc=560 N/mm2,For pinned ends-Factor…

Q: Water flows through the curved pipe shown in the figure below where point X denotes the center of…

A: Given: The discharge is 1 m3/s. The diameter of the pipe at the inlet is 0.5 m. The diameter of the…

Q: AW310 x 38.7 standard steel shape is used to support the loads shown on the beam in the figure.…

A:

Q: Please compare and contrast the stiffness vs force methods. Which is preferable for automation?…

A: It is indeterminate structure,  Need to identify using either force method and stiffness method.

Q: 3. (Tipler and Mosca, Physics for Scientists and Engineers, 5th Ed.) Consider three charges on a…

A:

Q: Part A For D = 1600 ft and R=550 ft, compute R₂ to fit the requirements of the figure and make the…

A: D = 1600 ft R = 550 ftTo find:Rx

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: For the pulley system shown in the figure below, which of the following statements are true?

A: Consider the FBD of pully A

Q: · A cantilevered beam is part of an assembly machine and is made of steel with round cross section…

A: Given 400lbf= 1780N

Q: Determine the pressure at the top of a 947.1 m tall building under the following conditions:…

A: Answer To calculate the pressure at the top of the building we have Pressure at the bottom of the…

Q: rades of g₁= -0.50% and 92 +3.50 %, VPI elevation 750.00 ft at station 30+00. xed elevation 753.00…

A: Finding length and rate of grade change.

Q: 1O N A GN

A:

Q: • Determine the reactions at supports A, B, C, and D: b.) using cantilever method K L 9 kN 4 m G E…

A: We have to determine the value of reaction at supports A, B, C, D and we have to use cantilever…

Q: You are the engineer supervising the layout of a piping system. In a certain portion of the pipe,…

A:

Q: In qualitative research, information collected is always filtered through the researcher and his/her…

A: Brief Concept Introduction- Qualitative Research- To comprehend people's attitudes, interactions,…

Q: True stress-strain behaviour of a metal is given by the flow curve equation σ = 1750 €0.37 where o…

A:

Q: The bracing for the moment-resisting frame used a channel section. Determine if the channel is…

A:

Q: A simply supported beam with spans of LAB = 8 ft and LBc = 24 ft supports loads of w = 4.5 kips/ft…

A: Maximum shear stress and Maximum bending stress in the beam.

Q: 2. Use method of members to determine the reactions in the supports and the horizontal and vertical…

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: me the reactions at the supports. - 4 m 500 N/m 30 4 m

A:

Q: F = 25kN 1) The socket wrench AB lies in the plane parallel to xy plane. 10kNm The assembly OAB is…

A:

Q: 2. s) According to Boussinesq and Westergaard conditions, determine the resulting load at a point 15…

A: 2We have formula for BoussinesqΔσ=Qz232π11+rz252We have formula for…

Q: a ga in tension with the following results: Applied 1 Strain Force (N) (mm) (%) 0 5.000 Stress (MPa)…

A: We…

Q: Highway curve has R = 800 m, I = 20° 00', and Pl station 3+290.600 m. Part A Determine degree of…

A: R=800mdegree of curvature=?

Q: A composite beam is under external loads as shown below. a) Draw the internal shear force and…

A:

Q: Given the loaded frame below, which is the bending moment diagram of member AB.

A:

Q: 7 1) 4)| Which of the following is true regarding the Moment- An internal hinge for the conjugate…

A: As per bartleby policy I can answer only 3 true/false question at a time. please re-upload again the…

Q: (3) ) A 6.0 m long simply supported beam is made of HN450×200×8 X 12, Q345steel. The beam carries on…

A: ALSO GIVEN CODE REQUIREMENTS FOR BENDING MEMBERS WITH CONTIOUS LATERAL SUPPORT IS AS BELOW:

Q: 2. A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of…

A:

Q: Set up the appropriate equation that is used to solve for the moment of inertia about the y axis.…

A:

Q: Q2. (a) Determine the maximum deflection of a cantilever beam at its free end subject to a uniformly…

A:

Q: Determine the force in each member of the truss, and state if the members are in tension or…

A:

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.