QN:1 Suppose that five strings pull one at a time on a horizontal beam that can pivot about a pin through its left end, which is the axis of rotation. Find the torque due to each forces T₁, T₂, T3, T4 and T5. (Each force is 200N and length of beam is /= 2m) Axis of rotation T 60° 1/2- T 2 60° 13 3 4 18 5 Is UT

QN:1 Suppose that five strings pull one at a time on a horizontal beam that can pivot about a pin through its left end, which is the axis of rotation. Find the torque due to each forces T₁, T₂, T3, T4 and T5. (Each force is 200N and length of beam is /= 2m) Axis of rotation T 60° 1/2- T 2 60° 13 3 4 18 5 Is UT

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The figure below shows forces acting at various points on a metal cylinder. The angles a = 50°, ß = 27°, y = 23°. The length { = 3.8 m. Find the net torque (in N• m) on the cylinder about the following axes. 25 N B. 10 N 30 N (a) an axis through O perpendicular to the page magnitude N: m direction ---Select--- (b) an axis through C perpendicular to the page magnitude N: m direction ---Select---
Calculate the net torque on the disk of diameter 0.350 m with respect to an axis passing through the center as shown in the figure. The 11.9 N force is perpendicular to the edge of the disk, while the 8.50 N force is tangent to the disk. 11.9 N 40.0° 14.6 N 8.50 N O 6.26 N.m O 5N.m O 4.5 N.m O 24 N.m 0.350 m
Spark plugs should be tightened to a specified torque of 7.65Nm. You have a wrench that is 0.37 m long, but because of the tightness of the space you can't pull the wrench at a ninety degree angle. You must pull at an angle of 36.04 degrees, measured from the handle of the wrench. What force must you exert on the wrench?
A 3.0-m rod is pivoted about its left end. A force of 6.0 N is applied perpendicular to the rod at a distance of 1.2 m from the pivot causing a ccw torque, and a force of 5.2 N is applied at the end of the rod 3.0 m from the pivot. The 5.2 N is at an angle of 25 degrees to the rod and causes a cw torque. What is the net torque about the pivot? Choose – 6.3 Nm –1.7 Nm 0.6 Nm – 0.6 Nm
The 31-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment of P about point B and about point A. Moments are positive if counterclockwise, negative if clockwise. C Answers: MB = MA= i i P = 31 N 1.7 m B 49° 1.7 m N.m N-m
A wooden door (as seen from above) has hinges on the left- hand side. In which direction of the applied force produces the largest torque? The magnitudes of all forces are equal. A B D F F C D OB Ο Α
A thin cord is wrapped around a uniform grindstone of radius 0.30 m and mass of 25 kg supported by bearings that produce negligible friction torque. The cord exerts a steady tension force on the grindstone, causing it to accelerate from rest to 60 rad/s in 12 s. (lgrindstone = 5 What is the magnitude of the tension force of the cord? O 5.6 N 11.3 N O 18.7 N O 37.5 N
Calculate the net torque about point O for the three forces (F₁=15.7 N, F₂=17.8 N and F3-20 N) applied on the rod as shown in the figure, where =25.2°. The rod and all forces are in the plane of the page. Assume the z-axis to be the axis perpendicular to the page. -12.0 m- 13.00 m 90.0⁰ 00 F₁ -4.00m- F2 10.3 m.N, about the z-axis 147 m.N, about the z-axis -66.5 m-N, about the z-axis 308 m.N, about the z-axis F3
plss answer correctly
Needs Complete typed solution with 100 % accuracy.
Problem 10: A long uniform-density beam has a mass M and a length L. It is hinged to a wall at its left end. A cable is attached to the middle of the rod as shown. A point mass m is attached to the far end. m. What is the correct N2L torque equation for this configuration? MultipleChoice : 1) T sin 0 – migL – M85 = 0 2) T sin 0 – m1gL – Mg = 0 L 3) T cos 0 - mīgL – Mg = 0 4) T cos 0 + m¡gL+ Mg¬ = 0 5) T sin 0 + mgL+ MgL = 0
A person exerts a horizontal force of 30 N on the end of a door 92 cm wide. a) What is the magnitude of the torque if the force is exerted perpendicular to the door? b) What is the magnitude of the torque if the force is exerted at a 70.0 ∘ angle to the face of the door?