Ql: (a) Using figure below, determine the collector current if Ig= 5 mA and VCB =15 V. Then determine the collector current if Ig remains at 5 mA but VCB is 5 V. (c) Using Figure 1 and 2, determine VBE if Ic = 3 mA and VcB = 10 V. + (A) te imA) Active region (unshaded area)- Ve 20 V Va= 10 V 5 MA VE IV 3 mA 2 mA I-1 A 20 0.2 04 0.6 Var (V) 15 Cutoff region Saturation region

Ql: (a) Using figure below, determine the collector current if Ig= 5 mA and VCB =15 V. Then determine the collector current if Ig remains at 5 mA but VCB is 5 V. (c) Using Figure 1 and 2, determine VBE if Ic = 3 mA and VcB = 10 V. + (A) te imA) Active region (unshaded area)- Ve 20 V Va= 10 V 5 MA VE IV 3 mA 2 mA I-1 A 20 0.2 04 0.6 Var (V) 15 Cutoff region Saturation region

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem-5 The LED in Figure below requires 30 mA to emit a sufficient level of light. Therefore, the collector current +Vcc should be approximately 30 mA. For the following circuit values, determine the Re amplitude of the square wave input voltage necessary to make sure that the transistor saturates. Use double the minimum value of base current as a safety ON ON margin to ensure saturation. OFF Vcc = 9 V, VCE(sat) = 0.3 V, Rc = 220 N, RB = 3.3 kÝ Bpc =50, and VleD = 1.6 V. 1
1- a. For the circuits given below calculate the currents through the zener diode (V5.1V) and the current through the Si-diode. 1k Ohm 1k Ohm -10V 1k Ohm 12V b. The emitter of an NPN type BJT is connected to ground. Its base is connected to a 5V supply with a 10K resistor. Its collector is connected to the same supply with a 6K resistor. Calculate the range of ß such that the transistor is not saturated.
8.
A. Detemine the value of the collector resistor in an npn transistor amplifier with Ppc = 250, VBB = 2.5 V, Vcc = 9 V, VCE = 4 V, and Rg = 100 k2. B. Detemine Icsat) for the transistor in below Figure. What is the value of IB necessary to produce saturation? What minimum value of VIN is necessary for saturation? Assume %3D VCE(sat) = 0 V. +5 V 10 kN Rg VINO BDc = 150 1.0 MN
Describe the application and use of Junction Field-Effect Transistors (JFETs)
A. Determine the VCE transfer as a function of Vi of the circuit in figure 1, (eliminating the zener diode), indicating the different areas of the transistor (Active zone VBE = 0.7v, VCEsaturation = 0.2v, VBSaturation = 0.8v; saturation zone: The transistor has a B = 110 and the reverse saturation current negligible. B. As in section a) with the zener diode, assuming that this is ideal, whose zener voltage is equal to 3.5Volts. R3=8K, R4=9K
For the JFET with maximum drain current 9mA, drain current 2.5mA at gate to source voltage 4V. Calculate the pinch off Voltage.
3. In a certain n-channel JFET, Ipss= 8 mA and Vp=-4 V. (a) Determine the value of Ves for maximum drain current. (b) Calculate the drain current for VGs=-5 V (c) Calculate the drain current for Ves=-2 V (d) Determine the maximum value of VGs for cut-off condition.
Kindly provide a CLEAR and COMPLETE solution.
Q1:- find the emitter, base and collector currents and VE. (let any parameters if you need). + Vcc=6 V 2 k2 530 kN
In N-channel E-MOSFET, as the VGS increases positively, the Drain current decreases. True or false
A common- configuration has the input at the base and the output iat the collector. base emitter collector