Q/A drawback of the integral gain Ki is that it can make the systemalternate ups and downs since when the error signal changes signTrueFalseQ/The derivative controller responded quickly, but also to overshoot.Another effect of increasing (K i) is that it tends to reduce the steady-stateerrorTrueFalseQ/ In general, the DC motor that has a stator made from the magnet issuitable in heavy industrial applicationsTrueFalseQ/Generally speaking, the series winding gives better starting torque, whileshunt winding gives better speed control.TrueFalseQ/The proportional-integral-derivative controller is the best controller forany dynamic systems.True

We are authorized to answer one question at a time, since you have not mentioned which question you…

Answered: Q/A drawback of the integral gain Ki is…

Q/A drawback of the integral gain Ki is that it can make the system alternate ups and downs since when the error signal changes sign True False

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The gain of the instrumentation amplifier IA is 800. Determine the gain of the circuit V. / VIN? Select one: 30 k2 O a. 160.0 Ob. 0.0 E IA Oc. 0.2 Od. 800.0 20 k2 80 kL Oe.
The calibration span of pressure transmitter is 0 to 100 psi. Can you show me the upscale and downscale calibration report showing 5 point calibration 0,25,50,75 & 100 percent results showing the analog milliampere and prcess variable results.
To a measurement range of -4 to 6 V, apply a 4-bit analog-to-digital converter. a- Identify the assigned voltages to each of the bins. b- Determine the voltage that will be assigned to a measurement reading -3.25 V. Calculate the percentage ADC error. c- Determine the voltage that will be assigned to a measurement reading 4.11 V. Calculate the percentage ADC error.
Which of the following statement is true? Conjugate matching guarantees the maximum output power regardless of input power. The optimum source impedance for the minimum noise figure can be obtained by conjugate matching condition. O The first stage is the most important to minimize the overall noise figure in cascaded blocks An oscillator cannot be built with a single stage amplifier. None of the above
As the magnitude of the error signal increases, the derivative control mode mode ; as the magnitude decreases, the derivative control
2) Dead space is defined as the range of different input values over which there is no change in output value. Select one: True False
What is the output peak voltage during the positive alternation of the input signal for the circuit shown below? •.. Vị 1+20V + Si vi 1.Ok Vo 5 V -20V A) 24.3 V B - 5 V - 24.3 V D) - 4.3 V
13. Pulse-amplitude modulation signals are multiplexed by using:a. subcarriers b. A/D convertersc. bandpass filters d. FET switches 14. A quantizer is a(n)a. multiplexer b. A/D converterc. demultiplexer d. D/A converter 15. Part of the PCM system that prevents aliasing:a. bandpass filter b. sample and hold circuitc. anti-aperture distortion d. both A and B
Q:: Read each statement carefully and answer by True or False (if False then, correct the statement). 1- Decrease the derivative time to reduce the effects of noise on feedback. 2- In the process systems, the integrator variables are always to be controlled because the integrators are unstable. 3- It is required to do a data validation before proceeding wiun une vmp.. modelling procedure. 4- Without a measurement filter, the noise does not go "around and around" in the feedback loop. 5- Feedforward control affects the stability of the Feedback control system when they are used together. 6- The statistical method has more calculations than process reaction curve method IIl when finding the empirical model.
(Asterisked problems are associated with optional sections.) 1. Determine the output of each of the following circuits, assuming that the upper input is 1 and the lower input is 0. What would be the output when the upper input is 0 and the lower input is 1? a. b. C. D D nia 00
indicate which of the signals 1, 2 and 3 of diagram 2, corresponds to the output signal of diagram 1 signal (signal c)
BW of an analog signal is 150 Hz. The sampling rate of ADC which :converts that signal to discrete form is between 100 and 200 sample/s 100 sample/s O Less than 100 sample/s O 200 sample/s exactly. O 300 sample/s or higher O