Q9: Replace the three forces acting on the shaft by a single resultant force. Specify where the force acts, measured from end C. C -4 ft- 13 12 260 lb 3 ft ft-211- -211-+- 200 lb -5 ft- 500 lb

Q: Find the forces in the three members of the space truss shown in the figure. 600 mm 500 mm 820 mm-…

A:

Q: The force magnitudes are F1 = 81 N and F2 = 22 N. The dimension h = 0.6 m and the dimension l = 0.5…

A:

Q: I just need the answers to 1,2,3. 1.The problem sketch shows _____ loads. 2.The moment load (the…

A: For the given arrangement  condition- The resultant of two forces is in vertical

Q: Please show magnitud and direction for every member forces) Use the method of MEMBERS to determine…

A: Force F = —1500 lb

Q: 75 kN force acts rightward at joint C and 200 kN force acts downward at joint D. Determine the axial…

A:

Q: Replace the loading shown by a single equivalent force. Specify the magnitude and direction of this…

A:

Q: Part A Y FR = Submit Part B In (Figure 1), ₁ = 2.5 kN/m and w2 = 7.5 kN/m Replace the distributed…

A:

Q: Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1…

A: Force F = —1500 lb

Q: The total torque of the forces on the ruler around a axis perpendicular to the ruler and passing…

A:

Q: Replace the force system by an equivalent resultant force and couple moment at point O (Figure 1).…

A: Given data:- F1= 24 lb F2=24 lb To find:- Resultant of force Angle of resultant Moment about point…

Q: lease ANSWER ALL of the given questions and show COMPLETE SOLUTION for each question.   I will…

A: Given Data : F=10 N d=2 m

Q: Add the following forces to find the resultant force. V1 = 150 g @ 470 V2 = 550 @ 324° V3 = 350 g @…

A:

Q: PROBLEM 1: Consider the force system shown with the following forces and given angles F₁ = 85 KN…

A:

Q: For the distributed load shown below, determine the equivalent force's magnitude and location,…

A: Given data: a=0.312 KN/m2b=1.08  KN/m2L=3.46 mw=(-ax2+bx)  KN/m

Q: Replace the loading system by an equivalent resultant force and couple moment acting at point A.…

A: Given : F₁ = 700 N F₂ = 300 N

Q: Turnbuckle T1 is tightened to a tension of 229 lb and turnbuckle T2 is tightened to 123 lb.…

A: According to the given data Co-ordinates the point- C=(32,0,60) ft D=(0,24,36) ft E=(-18,24,0) ft…

Q: A 2 ft F, 4 ft M B. - 3 ft- 30 -x F,

A: Given that, F1=150 lb,F2=50 lbM=500 lb.ft Consider the given frame, Resolve the given force in two…

Q: Determine the force supported by the roller at E.

A: Drawing the free body diagram of member as shown below, Consider member AC, Taking moment about A,…

Q: 5. Determine the principal stresses acting at point E by constructing Mohr's circle y. 150 mm 200 mm…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.