Q9:- It is required to transmit power of 500 kW from a driving shaft which is rotating at 1800 rpm to another shaft located at 660 mm approximately. If the speed ratio is 10 and standard gears are assumed with pressure angle of 22.5°, find:- (a) the nearest standard module if no interference is to occur, (b) the number of teeth on each wheel and the actual radii of the pitch circles, (c) contact ratio, (d) maximum sliding velocity and (e) the driving torque.

Q9:- It is required to transmit power of 500 kW from a driving shaft which is rotating at 1800 rpm to another shaft located at 660 mm approximately. If the speed ratio is 10 and standard gears are assumed with pressure angle of 22.5°, find:- (a) the nearest standard module if no interference is to occur, (b) the number of teeth on each wheel and the actual radii of the pitch circles, (c) contact ratio, (d) maximum sliding velocity and (e) the driving torque.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
Three 14.5° pressure angle spur gears with a diametral pitch of 8 are meshed. The input pinion on the left is running clockwise at 3101 rpm and transmits 3.2 Hp. Gear 1 (Pinion) Input N1 = 20 teeth Gear 2 Idler Gear 3 Output N3 = 25 teeth N2 = 75 teeth Answer the following: 1. Pinion (Gear 1) pitch diameter (1 mark) 2. Gear 2 pitch diameter (1 mark) 3. Gear 3 pitch diameter (1 mark) 4. Circular pitch (1 mark) 5. Addenda (1 mark) 6. Center distance from gear 1 to gear 3 (2 marks) 7. Line of action length for gear 1 contacting gear 2 (2 marks) 8. Contact ratio of gear 1 and 2 (2 marks) 9. Gear ratio from gear 1 to gear 3 (1 mark) 10. Draw a free-body diagram of Gear 2, showing the radial and tangential forces. Calculate these forces. What is the reaction force in the bearing? (3 marks)
Q12:- Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2.0. The module= 5 mm and the pitch line speed is 120 cm/sec and assuming the addendum as standard and equal to one Find:- (a) the angle turned through by when one pair of teeth is in mesh and (b) the maximum sliding velocity. module.
Q5:- The particulars of a pair of spur gear are:- (a) gear ratio=(1/10), (b) center distance3D 660 mm approximately, (c) power transmitted%3D 500 kW, (d) speed of the pinion= 1800 rpm, (e) teeth are of involute form with pressure angle= 22.5°, (f) the addendum= 1 module and (g) the permissible normal force between teeth is 200 N/mm of gear width. Find :- (a) the nearest standard module if no interference to occur, (b) the number of teeth on each wheel and (c) the necessary width of pinion and gear.
A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic load
Q4: The reverted gear train shown in Fig.(1) has the following data, Circular pitch Pc=D0.4 teeth/mm , T1=15, T2=30, T3=20 , N1= 150 rpm (cw) Determine: • 1. module of gear train (m3?) Output Input 2.Pitch diameter of gears (D1, D2, D3, D4) 3. The centre distance between shafts (C) • 4. Gear ratio (G), and Train value (TV) • 5. output speed (N4) 4/14/2020 27
A pinion shaft of a machine transmits a torque of 42 Nm to the shaft of gear at a speed of 578 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ( ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be approximatively 200mm, calculate the following:o Circular pitch value;o Number of teeth on the wheel (gear);o Number of teeth of the pinion;o Pitch circle diameter of the gear;o Pitch circle diameter of the pinion;
A spur gear reducer is to transmit 4 kW at 1500 rpm of the pinion of cast steel ( So=138 MPa). The gear is made from phosphor bronze (So=83 MPa). The velocity ratio is 3.5 to 1.0. Assume a pressure angle of 20°. Design the gears for strength only.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio