Answered: Q7. Explain what happen to a power…

Engineering

Electrical Engineering

Q7. Explain what happen to a power supply if there is no smoothing capacitor connected across the output?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Related questions

Q: Determine the values, of K and k of the closed-loop system shown in Figure below so that the maximum…

A: We need to find out unknown for given condition for given circuit .

Q: Why we use buck converter instead of using linear regulator?

A: We need to explain why we use buck converter instead of using linear regulator.

Q: b. The apparent power absorbed by the resistor c. The peak power absorbed by the resistor d. The…

Q: A shunt generator has a full load current of 196 amp. at 220 V. The stray losses are 720 watts and…

Q: 7. For the above Boost converter, what is the max voltage stress across S1 and S2? A. 10V, 10V Cazov…

Q: Explain the concept of power factor correction using a capacitor. List any two benefits of power…

A: Power factor correction is the process of improving the power factor of an electrical system by…

Q: What is characteristic impedance? How do you find it by measuring pulses?

A: Solution: Characteristic impedance is the resistance offered by a transmission line to the flow of…

Q: Comment briefly on the relationship between input and output power at varying excitation levels and…

A: Infinite Bus Bar is the bus bar where many(infinite) synchronous machines are connected. The…

Q: How does a capacitor bank improve power factor, and what are its applications in power system…

A: A capacitor bank is a collection of capacitors that are connected in parallel and used in electrical…

Q: what is the advantage of a capacitor start induction run motor over a resistance start induction…

A: The advantage of capacitor-start induction-run motor over resistance-start induction-run motor is…

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

Q7. Explain what happen to a power supply if there is no smoothing capacitor
connected across the output?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
What is transient stability in power system?
Comment briefly on the relationship between input and output power at varying excitation levels and on the relationship between excitation and power factor or reactive power, when the synchronous machine is connected to an infinite busbar
Explain the concept of power factor correction using a capacitor. List any two benefits of power factor correction.
How does a capacitor bank improve power factor, and what are its applications in power system control?
Find the parameters
Answer is 2.93 hz. Take No. Of poles = 2.
Please solve all parts
1. Impedance is the total opposition to an AC circuit caused by electric penalty tions, the tra capa multiple pacitive systema 62 Fundamentals of AC Electricity Questions for This C a. 1. Draw a diagram of an AC sine wave and identify its peak voltage and peak-to-peak voltage levels. b. 2. Explain the term frequency as it refers to AC electricity. c. 3. Discuss the difference between a load center and a fused disconnect. 2. WE wa 4. Explain how you would test for voltage in a fusible dis- connect on the line-side and load-side terminals. vi ci 5. Trace the path of a generated AC voltage from the generat- ing station where it is produced to the point where you would connect it to a machine in a factory. Be sure to iden- tify all the important parts of the system between the gen- eration station and the disconnect on the machine. a. be 3. True or False inductive reactance, capacitive reactance, and resistan 2. The units of impedance are
The brushes width in Wave winding is equal to a. 1.5 commutator segments. b. 1 of commutator segments. c. 1.25 commutator segments.
D. a Hall effect generator. 7. When power to a resistance load is controlled by full-wave SCRs with a 90° firing angle, what is the load power factor? A. 0.87 B. 1.0 C. 0.71 D. 0
Two identical 2,000 kW alternator operates in parallel. The governor of the first machine is such that the frequency drops uniformly from 50 Hz at no-load to 48 Hz at full-load. The corresponding uniform speed drop of the second machine is 50 Hz to 47.5 Hz. What is the maximum load that can be delivered without overloading either machine?