Q7: An automobile has a 3-liter SI V6 engine that operates on a 4-stroke cycle at 3600 rpm and produces a brake output torque of 205 N.m. The engine is squared and its compression ratio equals 9.5. At this speed air enters the cylinders at 85 kPa and 60°C, air-fuel ratio equals 15, and the mechanical efficiency of the engine is 85%. Take the heating value of fuel equals to 44 MJ/kg. Calculate: bore, stroke, mean piston speed, clearance volume per cylinder, brake power, indicated power, bmep, imep, bsfc, indicated thermal efficiency, brake thermal efficiency and the volumetric efficiency.

Q7: An automobile has a 3-liter SI V6 engine that operates on a 4-stroke cycle at 3600 rpm and produces a brake output torque of 205 N.m. The engine is squared and its compression ratio equals 9.5. At this speed air enters the cylinders at 85 kPa and 60°C, air-fuel ratio equals 15, and the mechanical efficiency of the engine is 85%. Take the heating value of fuel equals to 44 MJ/kg. Calculate: bore, stroke, mean piston speed, clearance volume per cylinder, brake power, indicated power, bmep, imep, bsfc, indicated thermal efficiency, brake thermal efficiency and the volumetric efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a diesel engine, r=18, α=2.8, T1=336 K, P1=100 kPa, Vh=740 cm3. The polythropic exponent in the compression process is nc=1.32 and the polythropic exponent in the expansion process is ne=1.36. The speed is n=2100 rpm and the number of cylinders is 6. Cp=1.0035 kJ/kgK, R=0.287 kJ/kgK, lower heating value of the fuel Hu=42.636 Mj/kg, combustion efficiency ɳc=0.96. a) Find the thermodynamic coordinates of the cycle. b) Find the indicated work and power. c) Find the amount of fuel the engine will consume per hour. d) If the cycle took place in an adiabatic state change: what would be the highest pressure and temperature in the cycle? Calculate.
The compression ratio in an air standard Otto cycle is 9. At the beginning of the compression stroke, the pressure is 0.1 MPa and the temperature is 21 C. The heat transfer to the air per cycle is 2000 kJ/kg. Use the PG model for air. I am trying to find the Mean Effective Pressure from this information
B1
Q₁) In an ideal otto cycle engine, the temperature and Pressure at the beginning of Compression are 43 C 100 kpa respectively and the temperature at the end of adiabatic Compression is 323%. if the temperature. at the end of Gnstant Volume heat addition is 1500°C calculate: (a) the Compression ratio, (b) the air- standard efficiency, (c) the temperature and pressure at the end of adiabatic expansion. Assume Yas 1.4 Por 2
An ideal otto engine , operating on the hot air standard with k= 1.3, has a compression ratio of 6.At the beginning of the compression the volume is 0.1982 cubic meter , the pressure is 15 psia and the temperature is 560 R .During the constant volume heating , 259 Btu are added per cycle . Find (a) c,(b) t3 ,(c) p3 ,(d) e, and (e) pm?
A spark – ignition engine has a compression ratio of 8.5 and a maximum temperature of 945.15K. At the beginning of compression stroke, P and T of the fluid are 0.1 MPa and 28.65 deg C. Assuming hot air-standard analysis, how much work (kJ/lb) is produced per cycle completion?
3. Define any four performance parameters of a gas turbine engine with the help of well-defined equations.
EX. 3: A petrol engine is supplied with a fuel of (41868 KJ/Kg) heating value. Cylinder pressure at (30%) of the stroke and (70%) of the stroke are (1.33 bar) and (2.66 bar) respectively. Assuming the compression isobying the Law PV=const. find the compression ratio if the relative efficiency compared with that of the ideal cycle is (50%). calculate the specific fuel consumption.
Hello, this is the problem attached below: An air-standard dual cycle has a compression ratio of 8.6 and displacement of Vd = 2.2 L. At the beginning of compression, p1 = 95 kPa, and T1 = 290 K. The heat addition is 4.75 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K.b) the net work of the cycle, in kJ.c) the power developed at 3000 cycles per minute, in kW.
I only need help with parts f to i. At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.1 L. Determine per cylinder: a) the volume at state 1.b) the air mass per cycle.c) the heat addition per cycle, in kJ.d) the heat rejection per cycle, in kJ.e) the net work per cycle, in kJ.f) the thermal efficiency in %.g) the mean effective pressure, in bar.h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar.i) Devise and evaluate the exergetic efficiency for the cycle.
I need the answer as soon as possible
pls answer part c, d and e