Q7: A three-phase, 60 Hz, squirrel-cage induction motor draws a current of 385 amps per phase and a total active power of 2344 kW when operating at full load from a 4000 volt (line) supply. The corresponding speed is 709.2 rev/min. The stator is star-connected and the resistance between twe stater live terminals is 0.1 ohms. The machine has 10 poles, the total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate: (6) the power factor at full load? (i) the active power supplied to the rotor? (ii) the total I'R losses in the rotor?

Q7: A three-phase, 60 Hz, squirrel-cage induction motor draws a current of 385 amps per phase and a total active power of 2344 kW when operating at full load from a 4000 volt (line) supply. The corresponding speed is 709.2 rev/min. The stator is star-connected and the resistance between twe stater live terminals is 0.1 ohms. The machine has 10 poles, the total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate: (6) the power factor at full load? (i) the active power supplied to the rotor? (ii) the total I'R losses in the rotor?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

New dishwasher circuits can be wired directly to NM cable. The circuit breaker is the disconnect. No answer text provided. OFalse No answer text provided. O True
NOTES: -Pls Do It By Using Computer Line, -(Minimum 350 words.) Reference must be mentioned at the end of the report.
i need the answer quickly
What 10 Wireless Equipment items need to purchase for a daycare business building?
15. _______ is a proximity sensor that uses the principle of ‘eddy current’ to sense the presence of an object.
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
Untitled form Your email address will be recorded when you submit this form. Not eng.refcon.k2324@sadiq.edu.iq? Switch account objective question(jW Jlgs) For the circuit shown below choose the correct answer V2 Vi SA 220 300 25A In 31
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
I need the answer as soon as possible
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
QUESTION 3 We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation.
Complete the following text with words Pt100 sensors are a specific type of _____(1) detector. The most important characteristic of Pt100 elements is that they are made of _____(2) with an electrical resistance of _____(3) ohms at a temperature of ______(4) °C and temperature coefficient ____(5). It is by far the most common type of RTD sensor. The other materials with which RTDs are built are: ___(6), _____(7), ______(8). The most recommended conditioning method is reading at _____(9). Typically, a _____(10) behavior of the Resistance-Temperature relationship can be assumed.