Q6. A hydro-cylinder with an inner diameter of D=200 mm has the oil pressure is p= 1 N/mm?.The cylindrical barrel and the flange are connected by eight uniformly distributed bolts. Therelative stiffness of the bolted connection is ka/(ks +kim) = 0.4. The applied preload is Qp =3F (Fis the operating force) and the allowable stress of bolt material is [0] = 150 N/mm?.(1) The total tensile load carried by each bolt;(2) The resultant load on the clamped members;(3) The minor diameter required for the bolts.

Answered: Image /qna-images/answer/973e60c6-57d4-4b9f-a6a4-c94980be7c88.jpg

Q6. A hydro-cylinder with an inner diameter of D=200 mm has the oil pressure is p= 1 N/mm?. The cylindrical barrel and the flange are connected by eight uniformly distributed bolts. The relative stiffness of the bolted connection is k/(ks +km) = 0.4. The applied preload is Q, =3F (F is the operating force) and the allowable stress of bolt material is [0] = 150 N/mm. (1) The total tensile load carried by each bolt; (2) The resultant load on the clamped members; (3) The minor diameter required for the bolts.

Q6. A hydro-cylinder with an inner diameter of D=200 mm has the oil pressure is p= 1 N/mm?. The cylindrical barrel and the flange are connected by eight uniformly distributed bolts. The relative stiffness of the bolted connection is k/(ks +km) = 0.4. The applied preload is Q, =3F (F is the operating force) and the allowable stress of bolt material is [0] = 150 N/mm. (1) The total tensile load carried by each bolt; (2) The resultant load on the clamped members; (3) The minor diameter required for the bolts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You have the thin walled pressure vessel shown. Given the dimensions of the pressure vessel, will the pressu fail (based on the yield strength)? Justify your answer with numbers Material and Pressure Material A36 Steel Pressure 0.75 ksi Tank Properties Inner Radius 3.00 ft Length Wall Thickness 10.00 ft 0.25 In
Consider the following spring arrangement. If k1 = 23.92 N/m, k2 = 26.58 N/m, k3 = 40.68 N/m, and F = 79.29 N, what is the equivalent spring constant (N/m) of the given multi-spring system? (Use 2 decimal places for the final answer.) k3 wwwwwwwwww. k₂
4kN/m uniform spring load h = 2b allowable normal stress 12MPa h(min) = ?
The squared and grounded ends of a safety valve with 7.5 coils. The coils measure 105 mm in diameter on the outside and 17 mm wire diameter. It measures 210 mm in free length. 82 Gpa is the modulus of rigidity. Calculate the initial compression length of the wire required to maintain a boiler pressure of 1.35 Mpa on a 30 mm diameter valve seat. (Draw the diagram)
H.W: Design a cast iron rigid type flange coupling to transmit 20 kW at 900 r.p.m. from an electric motor to a compressor. The following permissible stresses may be used: Shear stress for shaft, bolt and key material =40 MPa Crushing stress for bolt and key = 80 MPa %3D Shear stress for cast iron =8 MPa Draw a neat sketch of the coupling.
= tan-¹ μs The Clamp: Ex.1 (Part 1/2) 24 ?w=? us= 0.3 = 16.7° a) Fon block= FP-400N Lead=4mm T=40Nm D=10mm R=10cm F = FP W F Lead angle Lead 0 -2πr- [0] Φ 10
Toe Hinge-Pins Hel The brake shown in Fig. 1 is R=170 mm inner radius of the drum and is actuated by two hydraulic pistons that exerts the same force F =2800N, on each shoe. The shoes are identical and have the same unknown face width. The lining material has a coefficient of friction u=0.3 and a maximum pressure of P3=1050 kPa. The other dimensions are e = 130°, a = 21° B = 29°, p = 150 mm, d = 47 mm %3D Determine the (a) The face width in millimeters. (b) Pressure in the left-hand shoe in (kPa). (c) The braking torque in (Nm).
Please help. Written on paper not typed on computer please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Draw the acceleration polygon. Show Transcribed Text C U From the drawn polygon, find angular acceleration of link 2 (link BC) and the translating acceleration of the block C.
The induced nominal stress in a machine member is 33 N/mmn and the value of maximum stress near the irregularities is 59N/mm2, the value of stress concentration factor is SCF, K =
A flanged bolt coupling consists of six 2-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four 3/4-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied without exceeding 6000 psi in the steel or 9000 psi in the aluminum? Assume Gst = 12 × 106 psi and Gal = 4 x 106 psi.
With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 5 answers is correct