Q6. A 50 Hp 250V, 1200 R/Min DC shunt motor with compensating winding has an armature resistance (including the brushes, compensating winding and inter poles) of 0.06 ohms. If the field resistance Radi + R, is 50 ohm which produces no load speed of 1200r/min. there are 1200 turn ner pole on the shunt field winding. CLO-2, PLO-3|] (Marks- 5) A. Find the speed of the motor when its input current is 100A, 200A and 300A.

Q6. A 50 Hp 250V, 1200 R/Min DC shunt motor with compensating winding has an armature resistance (including the brushes, compensating winding and inter poles) of 0.06 ohms. If the field resistance Radi + R, is 50 ohm which produces no load speed of 1200r/min. there are 1200 turn ner pole on the shunt field winding. CLO-2, PLO-3|] (Marks- 5) A. Find the speed of the motor when its input current is 100A, 200A and 300A.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

To modeling separated excited DC motor by transfer function, you need to Trus Fuc block to get the represent armature current la field current If Speed Wr electromagnetic Torque Te *
Complete the blank If pole is 6 and Synchronous speed is 40 rev/sec of an induction motor , then the frequency f =..................................?
Derive the power equation for DC motor. Give the different load-torgue curves for each, DC. motors
A 200 V D.C. shunt motor takes 20 A at rated voltage and runs at 1000 r.p.m. Itsarmature resistance is 0.1 ohm. Calculate the value of additional resistance requiredin the armature circuit to reduced the speed to 800 r.p.m when the load torque isindependent of the speed.Ignore the field current. (Ans.1.98 ohm)
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If this DC machine is operating as a motor with rated flux at rated speed, calculate the rated torque (TR), rated current (IR), rated voltage (VR), efficiency (n) at the rated point, taking into account the winding losses. Find the speed (@NL) of this motor in no-load condition. TR Nm IR А VR V Eff = % ONL= rpm
A 10 kW, 250V shunt motor has an armature resistance of 0.5ohm and a field resistance of 200ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3A. At full load and rated voltage, the current line is 47A and because of armature reaction, the flux is 4% less than it no load value. (a.) What is the full load speed? (b.)What is the developed torque at full load? 1158 rpm
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
12. The IR-compensation in frequency control of induction motors is used for: a) compensation of the voltage drop in the active resistance of the stator winding. b) compensation of the voltage drop in the inductive reactance of the stator winding. c) keeping the motor voltage constant. d) keeping the motor speed constant U₁ U₁ Us0 0 f. f₁
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. Determine: (i) The synchonous speed. (V) speed at half Load (ii) The motor speed. (iii) The rotor frequency. (iv) The slip speed. ...A... -
Describe the basic circuit of DC Generators including its yoke, fid windings, interpoles, fieldpoles, difference of shunt coils and series coils, commutator and brushes ?
A 500 V DC shunt motor takes 4 A at no-load. The shunt field winding resistance and the armature winding resistance are 250 and 0.2 respectively. Find the efficiency when the motor draws a current of 10 A at full load.