Q6: find the transfer function Xo(s)/Xi(s) of the mechanical system shown in Figure (a). Also find the transfer function Eo(s)/Ei(s) of the electrical system shown in Figure (b). Show that these transfer functions of the two systems are of identical form and thus .they are analogous systems R2 k1 by C2 R1 b2 Xo eo ww

Q6: find the transfer function Xo(s)/Xi(s) of the mechanical system shown in Figure (a). Also find the transfer function Eo(s)/Ei(s) of the electrical system shown in Figure (b). Show that these transfer functions of the two systems are of identical form and thus .they are analogous systems R2 k1 by C2 R1 b2 Xo eo ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Given that the input V1(t) in Figure 4 (a) is a 3V peak triangle wave at 4 kHz.Answer the following 2.The circuit in Figure 4 (b) has 5 op-amps labeled as U1 through U5. State what the op-amp circuit is for U1 Circuit: U2 Circuit: U3 Circuit: U4 Circuit: U5 Circuit: 3. Determine the values of VO1, VO2, VO3, VO4 and VO5. 4. Draw the output waveform at VO5 for the given input waveform shown in Figure 4 (a).
a circuit design for AB' + AC' + AD' + BCD Thank you!
B6
4
I need answer in your hand Design a buck-boost converter to supply a load of 100 W at 60 V from a 30 V source. The output ripple must be no more than 2 percent. Specify the duty ratio, switching frequency, inductor size, and capacitor size.
(i) For the circuit below, draw the output waveforms for both the given input wave- forms. (ii) How can you convert this circuit into a half-bridge by removing any two compo- nents? Please draw a circuit diagram. Also, draw the current flow through the modified circuit. This can be done by annotating the modified circuit diagram. M (i) (ii)
Question 1: a) Sketch Vo versus time for the circuit shown with the input given. b) Determine DC output voltage without a capacitor. c) If a capacitor of 10 uF is placed in parallel with RL, sketch the vo versus time. d) find the DC output voltage. Given R1 = R2 = RL = 2.2 k2. Vi +40 D1. D2 10 ms R = 2.2 k2 ww R%3D 1GF R = -40 2.2 k2 2.2 k2
shows a block diagram of a process con- trol system. Determine the range of the gain K for stability. Figure K Figure Process control system. Verify using Nyquist on Matlab
please show the step claerly
Sketch the output voltage waveform for each op armp circuits given below. Given the maximum outputvoltage for the op-armp is Vomax = +10 v and Vomin = -10 v.Use input voltage for all circuit as shown. Also use V2 = 4.7 V for D1 and D2. V. 0 -5V- -5V D1 Kt 1K 1K D2 V1 V2
3) Load for a circuit with direct current source voltage The waveform of the voltage generated on it is below shown. Source for this working circuit that is symmetrical The value of the voltage and load resistance is 100 V and 5Ω respectively.It is given as. Find what is required below. d) Find the effective value of the output voltage e) Total harmonic distortion in output voltageCalculate (THD)
The output response is as in figure-b, while applying the unitstep function to the system input given in the figure-family block diagram belowis happening. T and are the constant numbers seen in the open loop transfer function. Calculate the constant.