q5(c) Using Rayleigh theorem, estimate an expression for the drag force on a smooth sphere of diameter, D moving with a uniform velocity, V in a fluid density, ρ and dynamic viscosity, μ. Refer to Table 5(c). TABLE Q5(c)Dimensi (Dimesion)No.KuantitiQuartitySistem M-L-TSistem F-L-TFInidamentd QuantitiesMass mKnantiti AsasiJism mMFL-'T²Panjang LMasa tLength LTìme tTKnantiti GeometrikLuas AIsipadu VMomen inersiaGeometric QuaitifiesArea AVolime VB4L5L3L3Moment of tmertiaKinematic QuaitifiesLinear velocity U, VAngular velocity oRotational speed NAcceleration a6.L4L4CKnantiti KinenatikHalaju linea U, VHalaju sudut aHalaju putaran NLT-LTT-1T-1T-1T-1LT-2T-2LT2T-210Pecutan aPecutan sudut aAngular acceleration aFlow rate QGravity gKinemdic visCosity vStrecan fiunction yCirculaion I11Kadar alir QGraviti gLT-LT-2LT-LT-2LT-IL²T-1LT-113LT-IL²T-1LT-114Kelikatan kinematik vFungsi arus yPutaranVortisiti 2151617Vorticity 2Knantiti DinaikDaya FKetumpatan pBerat tentu yKelikatan dinamik uTekananpTegasan ricih zModulus keanjalan E, KDynamic QuantitiesForce FDensity pSpecific weight yDynconic viscosity iPressire pShea stress tModilis of elasticity E, KMLT²ML-318FFL-T?FL19ML-T2ML-'T-1ML-'T-2ML-'T-2ML-IT-22021FL-T22FL223FL224FT25MomentumMomentumMLT-FLTAngular momentonMoment of momentionWorkWML?T-1ML?T-1ML²T-2ML²T-2ML?T-226Momentum sudutFLT27Momen momentumFL-T?Kerja WTemaga ETorque T28FLEnergy ETorque T29FL30FL31Kuasa PPower PML?T-3FLT-

Dimensional analysis is a method of dimensions. It is a mathematical technique used in research work…

q5(c) Using Rayleigh theorem, estimate an expression for the drag force on a smooth sphere of diameter, D moving with a uniform velocity, V in a fluid density, ρ and dynamic viscosity, μ. Refer to Table 5(c).

q5(c) Using Rayleigh theorem, estimate an expression for the drag force on a smooth sphere of diameter, D moving with a uniform velocity, V in a fluid density, ρ and dynamic viscosity, μ. Refer to Table 5(c).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
Find an expression for the drag force on a smooth sphere of diameter D, moving with a uniform velocity V .In a fluid of density p and dynamic viscosity µ. Use Rayleigh's method.
Fluid material subject.
An incompressible fluid is flowing at a steady rate in a horizontal pipe. From a section, the pipe divides into two horizontal parallel pipes of diameters di and d2 (where d₁ = 4d₂) that run for a distance of L each and then again join back to a pipe of the original size. For both the parallel pipes, assume the head loss due to friction only and the Darcy-Weisbach friction factor to be the same. The velocity ratio between the bigger and the smaller branched pipes is
Explain force of friction between two bodies. If a wooden block of weight 100 N rests on a horizontal plane. Determine the force required to just (a) Pull it and (b) Push it. Take coefficient of friction equal to 0.4 between the sliding surfaces.
A film-shaped Newtonian fluid flows from top to bottom in the direction of gravity from the inner surfaces of a cylindrical vertical pipe of length L. The radius of the pipe is R and the distance from the center of the pipe to the liquid surface is aR. Let the viscosity and density of the fluid be constant. Assuming that the pressure variations in the fluid inlet and outlet are negligible a) Write the expressions describing the system using the continuity equations for the steady state and derive the equation that gives the velocity distribution of the fluid. b) Considering that the pipe is pulled up at a constant V velocity, rearrange the equation that gives the velocity distribution NOTE: Analytical solution and numerical solution will be made. R V i aR
Consider a fluid of viscosity μ between two circular parallel plates radie 'R' separated by a distance h upper plate is rotated at an angular velocity w where as bottom plate is held stationary. The velocity profile between two plate is linear. The torque experienced by the bottom. plate is?
help pls