Q5. In the image shown below, the 3.6-kg collar is connected to a spring with unstretched length of 1.8 m, and spring constant k = 8 N/m. Determine the elastic potential energy of the collar. Negative sign must be included if the energy is negative. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point, and proper SI unit. Take g = 9.81 m/s². Your Answer: Answer k 4 m units 3 m

Q5. In the image shown below, the 3.6-kg collar is connected to a spring with unstretched length of 1.8 m, and spring constant k = 8 N/m. Determine the elastic potential energy of the collar. Negative sign must be included if the energy is negative. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point, and proper SI unit. Take g = 9.81 m/s². Your Answer: Answer k 4 m units 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shear Force Diagram and Bending Moment Diagram Determine the equations to draw the shear force diagram and bending moment diagram. Consequently, draw the shear force and bending moment diagram for the following load diagram. 2. 37 kN A 1.00 M 2.00 M
A metal rod of length L=8.88 has only three forces applied to it in the directions shown in the diagram below. Force #2 is applied at the midpoint of the rod. If the rod is in static equilibrium and the magnitude of force #1 is 7.15, what is the magnitude of force #2?
HW4 Q9
Just need help and explanation on this question, wasn't discussed in class. Thanks!
Please walk me through the process of arriving at my answer.
Determine the tension developed in the cable AC required to support the traffic light Express your answer to three significant figures and include the appropriate units. HA ? FAC = Value Units Submit Request Answer Part C Figure 1 of 1 Determine the tension developed in the cable AD required to support the traffic light Express your answer to three significant figures and include the appropriate units. 6 m ? HA 3 m FAD = Value Units 4 m 4 m Submit Request Answer 3 m 4 m 6 m 4 m 3 m y Provide Feedback
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Q4. When a tensile load (F) is applied to a solid homogeneous rod, the rod undergoes a change in length (AL) within its elastic region of proportionality, The strain energy (U) can be calculated using the following equation: FΔL U= 2 а. F² A 2LE O b. F² AL 2ΕΔL O c.
A 50.0N weight uniform 4 metre long beam is hanging from a cord held out at a 30° angle as shown. And unknown weight not shown in the diagram is also hanging 1 m from the X on the diagram. A) The tension in the cord is measured with a spring balance and found to be 130 N. find the counter clockwise torque from the cord about the X shown in the diagram. B) balance torques to find the torque from the unknown weight that is not shown in the diagram Hint: add the unknown weight to the diagram and do not forget to include the weight of the beam in your calculation
1) Calculate the magnitude of the force in the elbow joint in units of newtons.
Civil engineering
I need help with this question, it really has me stumped. The values I have depicted are said to be incorrect, I have also tried the same values but positive for each part and it was incorrect as well. Any help would be appreciated, thanks.