Q5) In a certain experiment, cylindrical samples of diameter 4 cm and length 7 cm are used. The two thermocouples in each sample are placed 3 cm apart. After initial transients, the electric heater is observed to draw 0.6 A at 110 V, and both differential thermometers read a temperature difference of 10°C. Determine the thermal conductivity of the sample. Answer: 78.8 W/m C

Q5) In a certain experiment, cylindrical samples of diameter 4 cm and length 7 cm are used. The two thermocouples in each sample are placed 3 cm apart. After initial transients, the electric heater is observed to draw 0.6 A at 110 V, and both differential thermometers read a temperature difference of 10°C. Determine the thermal conductivity of the sample. Answer: 78.8 W/m C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.21P

See similar textbooks

Similar questions

Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
A chromel–constantan thermocouple measuring the temperature of a fluid is connected by mistake with copper–constantan extension leads (such that the two constantan wires are connected together and the copper extension lead wire is connected to the chromel thermocouple wire). If the fluid temperature was actually 250 C and the junction between the thermocouple and extension leads was at 90 C, what e.m.f. would be measured at the open ends of the extension leads if the reference junction is maintained at 0 C? What fluid temperature would be deduced from this (assuming that the connection error was not known)?
= Consider a large plane wall of thickness L=0.3 m, thermal conductivity k = 2.5 W/m.K, and surface area A = 12 m². The left side of the wall at x=0 is subjected to a net heat flux of ɖo = 700 W/m² while the temperature at that surface is measured to be T₁ = 80°C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary equations for steady one- dimensional heat conduction through the wall, (b) obtain a relation for the variation of the temperature in the wall by solving the differential equation, and (c) evaluate the temperature of the right surface of the wall at x=L. Ti до L X
A pressure spring type thermometer having a time constant of 1.7s is placed in boiling water at a temp of 212F after being at a temperature of 69F. Determine the thermometer reading after 3.4s? Show detailed solutions
3. A cylindrical pipe of negligible thickness holding a hot fluid at 140°C and having an outer diameter of 0.4 m is insulated with three layers of each 50 mm thick insulation of k₁ = 0.02: k2 = 0.06 and k3 = 0.16 W/m-K (starting from inside). The outside surface temperature is 30°C. Solve for the value of T2 (°C). • show conversions, units, and box in your final answers
2 kilograms of gas with a molecular weight of 28 is closed and equipped with an electrical resistor. located in a rigid tank. This system has a fixed resistance of 10 amps and a voltage of 12 volts for 10 minutes. is implemented. When thermal equilibrium is reached, it measures that the temperature of the gas rises by 40.3°C. shows. It is estimated that the heat transfer to the environment occurs as 20 W. With the help of the measured data and assuming the ideal gas behavior, the gas's Determine the average value of the specific heat Cp in kJ/(kg K).
Thermistors are semiconductors used for measuring temperature. The electri- cal resistance of a thermistor changes with temperature. One model for the et- fect of temperature on a specific thermistor is R = 2,252e4000(-36.16), where R is the resistance in ohms and T is the temperature in K. You can verify that this thermistor has a resistance of 2,252 at 25°C = 298.16 K. For the data below, calculate the correlation coefficient for the model and decide whether the model fits the data well or not. Temperature (°C) Resistance (N) 7,850 10 4,400 2,900 20 1,500 30 1,000 40
., In a certain experiment, cylindrical samples of diameter 4 cm and length 7 cm are used (see Fig. 1-29). The two thermocouples in each sample are placed 3 cm apart. After initial transients, the electric heater is observed to draw 0.6 A at 110 V, and both differential thermometers read a temperature difference of 10°C. Determine the thermal conductivity of the sample. Insulation Resistance heater Sample Sample Cooling fluid Thermocouple a AT₁ LAT, Cooling fluid
A body having a cylindrical shape of length equals temperature is equal to 300 K. The initial temperature of the body is equal to 350 K. If the heat convective coefficient is equal to 4.2 W/m^2.K. What condition should the thermal conductivity k verify in order to apply the lumped capacitance method. 1.9 m and diameter equals to 400 mm is inside a room where the ambient Select one: a. k is less than 4.2 W/m.K b. k is greater than 1.6 W/m.K O c. k is greater than 3.8 W/m.K O d. k is less than 2.1 W/m.K
The TPD method measures temperature elevations in a tissue region during a heating pulse and its later temperature decay after the pulse. It is then using the Pennes bioheat equation to perform a curve fitting to determine the local blood perfusion rate. If the TPD probe is placed in the vicinity of very large blood vessel, will the TPD technique provide an accurate measurement of the local blood perfusion in the vicinity of this large blood vessel? Explain briefly. (Hint: Is the Pennes bioheat equation accurate surrounding a large blood vessel?)
A team of students tests a material for its thermal conductivity (k). After 20 minutes in a heat box, the temperature is 48° C inside the box and 28° C on top of the material. The following data is true about this test: Area of material = .0225 m2 Thickness of material = .0127 m Light bulb = 25 W What is the thermal conductivity constant for the material? Calculate the amount of energy transferred through the material. Determine the R-value of the material. Based on your calculations, would the material be a reasonable choice for home insulation? Yes of No
Answer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg.°C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1. Schematic of temperature distribution 2.ΔTLMTD 3.Actual heat transfer rate 4.Cmin 5.Maximum heat transfer rate