Q5/ A transmitter is angle modulated with a 1 KHz sinusoid to generate the signal : O (t) = 30 COS (6COS 2T ×10° t + T x 10 t) If the modulation is FM, determine: a- Modulation index and peak frequency deviation. b- Carrier and information frequencies. c- The total average power with 500 2 load.

Q5/ A transmitter is angle modulated with a 1 KHz sinusoid to generate the signal : O (t) = 30 COS (6COS 2T ×10° t + T x 10 t) If the modulation is FM, determine: a- Modulation index and peak frequency deviation. b- Carrier and information frequencies. c- The total average power with 500 2 load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

XY is 84, thanks
Single Sideband Modulator Using Phasing Method
What are the different form of amplitude modulation? Give comparison between them
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
In an amplitude modulation process, write what name the signals indicated in diagram 1 receive A) signal at frequency of 1400kHz B) signal b with a bandwidth of 300Hz to be transmitted C) Signal c
An AM waveform has a maximum span of 7.5V while minimum span of 2.5V. Determine the modulation index and the transmission efficiency.
The carrier frequency is 500 Hz, and the modulating signal is a single- tone sinusoidal signal. The x-axis is in time while the y-axis is the amplitude of the AM signal. Determine the power of the unmodulated carrier in W. Assume the load resistance to be 1-ohm. 4 3 1 -1 2 -3 -4 -5 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
1. Calculate the total power of AM signal (par-A). 2. Calculate the bandwidth of AM signal (part-A). 3. Draw the spectrum of AM signal (part-A). DC Vmax Vmin m 3v 1.4 0.25 0.7 2v 1 0 1 1v 0.8 -0.36 1.94
An FM transmitter operates on a frequency of 100.3 MHz. The modulating frequency is 15 KHz. The maximum FM deviation is 075 kHz. What are the maximum and minimum frequencies that occur during modulation? What is the rate the carrier changes frequency?
Problem1: the figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: 1. What is the modulation scheme in A? 2. What is the modulation scheme in B? 3. What is the sampling frequency? 4. What is the value of the duty cycle in A?
4. In an Amplitude Modulation: a) Amplitude of the carrier varies. b) Frequency of the carrier remains constant. c) Phase of the carrier remains constant. d) All of the above.
Sub:communication Need solution please