Q4:Choose the correct items of the following statements: 1-The output voltage of an emitter follower is a-In phase with Vin - b-Much greater than Vin. c-180° out of phase. d-Generally much less than Vin- 2-The ac emitter resistance of an emitter follower a-Equal the de emitter resistance. b-Is larger than the load resistance. c-Is B times smaller than the load resistance. d-Is usually less than the load resistance. 3-A common-base amplifier can be used when a-Matching low to high impedance. b-A voltage gain without a current gain is required. c-A high- frequency amplifier is needed. d-All of the above. 4-If the voltage generator is 5 mV in an emitter follower, the output voltage across the load is closest a-5 mV. b-150mV. c-0.25 mV. d-0,5 mV,

Q4:Choose the correct items of the following statements: 1-The output voltage of an emitter follower is a-In phase with Vin - b-Much greater than Vin. c-180° out of phase. d-Generally much less than Vin- 2-The ac emitter resistance of an emitter follower a-Equal the de emitter resistance. b-Is larger than the load resistance. c-Is B times smaller than the load resistance. d-Is usually less than the load resistance. 3-A common-base amplifier can be used when a-Matching low to high impedance. b-A voltage gain without a current gain is required. c-A high- frequency amplifier is needed. d-All of the above. 4-If the voltage generator is 5 mV in an emitter follower, the output voltage across the load is closest a-5 mV. b-150mV. c-0.25 mV. d-0,5 mV,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. Illustrate any differences or similarities between BJT and FET. b. Draw the V-I characteristic of an ideal diode Model. c. Draw the circuit symbol of a common emitter configuration of an NPN transistor.
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
A silicon controlled rectifier (SCR) has a forward breakdown voltage of 230 V. When a gate current of 2 mA flows in the gate circuit. If a sinusoidal voltage of 400 V peak is applied, find the following: Firing angle. Average output voltage. Average current for a load resistance of 180 Ohms. Power output
4
In a Bread Board, the rows are shorted or the columns are shorted? The BJT is operated in The Zener diode may have a breakdown voltage from about mode. Transistor has doped regions. Which one is the full form of DMM? In forward region Zener diode Clipper Circuits When the diode is connected across a voltage source with positive polarity of source connected to P side of diode and negative polarity to N side, then the diode is in A rectifier converts an In Full-wave bridge rectifier how many diodes are needed? condition. signal into a signal.
Design the power supply using diode components. This power supply sholud have 2 outputs. 12Vdc and 5Vdc. Input 240 Vac Supply i. Draw the circuit diagram ii. Bill of material/components that will be used iii. Teh output waveform for each stage
Please answer (d), (e), and (f). Part (d) is mislabeled as the second part (c).
3. Draw a half wave and full wave rectifier circuit with 1 KQ load resistance and sketch the output waveforms when the input is 10 V sinusoidal signals. Also find the de values for both the circuits.
Draw schematics for the following circuits/components: a) And Gate b) Rectifier circuit c) NPN BJT Amplifier with current directions d) OR Gate c) Diode