Q4/A volute centrifugal pump with an impeller diameter of 0.02 m has the following performance data when pumping water at the best efficiency point (bep). Impeller speed N = 58.3 rev/s capacity Q = 0.012 m3/s, total head Ah = 70 m, required NPSH = 18 m, and power = 12,000 W. Evaluate the performance data of a homologous pump with twice the impeller diameter operating at half the impeller speed, Then Calculate the specific speed for these two pumps.

Q4/A volute centrifugal pump with an impeller diameter of 0.02 m has the following performance data when pumping water at the best efficiency point (bep). Impeller speed N = 58.3 rev/s capacity Q = 0.012 m3/s, total head Ah = 70 m, required NPSH = 18 m, and power = 12,000 W. Evaluate the performance data of a homologous pump with twice the impeller diameter operating at half the impeller speed, Then Calculate the specific speed for these two pumps.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Given: Two (2) identical pumps connected in parallel has the following data: Suction Pressure…

Q: Hello i have an example with an answer , please show the solution since only the answer was shown in…

Q: A two-lobe rotary positive-displacement pump, similar to that of Fig, moves 3.64 cm3 of tomato paste…

A: Given data

Q: . centrifugal pump rotates at 750 rpm. Water (p=1000) inters the impeller normal to blades (á = 0°)…

Q: Q.1 Acentrifugal pump running at 500 rpm and at its maximum efficier is delivering a head of 30 m at…

A: To find: The head H in meters and flow rate Q in liters per minute at maximum efficiency. Given: The…

Q: ce an angle of 28° velocity direction

Q: milar centrifugal pumps are connected in series. The theoretical hea elation of Pump#1 is given by:…

Q: A centrifugal pump has the following specifications: d1 = 12 in., d2 = 24 in., b1 = 2 in., b2 = 1…

A: Draw a diagram showing the inlet velocity triangle. Here, u1 is the blade velocity at the inlet, v1…

Q: A centrifugal pump is used to lift water from a water reservoir with level 1 m below the pump center…

Q: Ah against capacity Q pump and system curves for both pumps running on the basis of the O1. Two…

Q: A 4x3-13 1750 rpm centrifugal pump equipped w/ an 11-inch diameter impeller requires 14.3bhp when…

Q: 4.1 The bucket ofa Pelton wheel which rotates at 100 rpm deflect the jet with diameter 50 cm through…

A: NOTE:- As per our company guidelines we are supposed to answer only 3 sub-parts. Kindly repost other…

Q: A form stage centrifugal pump running at 600 rpm is to deliver I m'/s of water against a manometric…

Q: B-A pump has the following parameters N=2133.5 RPM, Ns = 40 RPM, D= 37.1 cm and is used to pump…

Q: ро 3. VB Pumpe -Vinn We have a boat wit a constant speed V_B and a constant volumetric flow rate Q…

A: Given: The flow rate, Q = 20 l/s The density of water, ρ = 1000 kg/m^3 The gravitational…

Q: 1. List major differences between nonpositive displacement and positive displacement pumps.

A: To find :- Difference between non positive displacement versus positive displacement pump.

Q: The characteristics for a pump are given in the table below. The pump is required to left water…

Q: (d=0.85, -0.01 Pas and P-90 kPa abs.) from an open pressurized tank B, as illustrated in Figure 1. A…

A: NA

Q: 17. A centrifugal pump hás a 25 cms diameter impeller and an outlet width of 5 cms and runs at 1100…

A: Given: Diameter of the impeller D2=25cm or 0.25m ( Diameter of the impeller means diameter at the…

Q: charge of 74 L/s and shockless entry

A: Given-Information:- Inlet Radius, r1 = 71 mm = 0.071 m Outlet Radius, r2 =154 mm = 0.154 mWidth at…

Q: Q2/ A pelton turbine rotates at angular speed of 150 r.p.m, developing 67 KW under a water head of…

A: It is a thermodynamic cycle that describes the process that is useful for power generation by…

Q: Q5/ A centrifugal pump impeller runs at 1500 rpm & has internal & external diameters of 0.2 n & 0.4…

A: A centrifugal pump is a mechanical device that moves a fluid by transferring rotational energy from…

Q: Pump has a displacement of 98400 mm". It delivers 91.2 Lpm of oil at 1000 rpm and efficiency is 81.7…

Q: A centrifugal pump rotates at n = 1160 rpm. Water enters the blades radially. The outlet radius is…

A: Given:Pump speed, n=1160 rpmOutlet radius, r2=9 in=912ft=0.75 ftBlade width, b2=2 in=212ft=0.1667…

Q: A centrifugal pump has impeller with dimensions r1 = 78 mm, r2 = 143 mm, b1 = 54 mm, b2 = 26 mm, β1…

Q: A submersible pump of 80 percent efficiency is used in pumping water with flow rate, Q from a river…

Q: 2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria…

Q: Two(2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95…

Q: A certain centrifugal pump was tested and its performance curves can be approximated as follows: H…

A: INTRODUCTION: Pumps are used to raise water and transport it to its final destination. Pumps are…

Q: A ce folla

Q: Q4) A) A radial, multistage, four impellers, keyed to the same shaft, centrifugal pump is…

Q: al flow pump

A: diameter= 0.59m minimum speed ratio= 0.83

Q: B-A pump has the following parameters N=2133.5 RPM, Ns = 40 RPM, D=37.1 cm and is used to pump water…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three sub…

Q: A pump, geometrically similar to the 12.95-in model inFig. , has a diameter of 24 in and is to…

A: For water, ρ1 = 1.94 slug.ft3For gasoline, from Table A.3, ρ2 = 680 kg/m3 = 1.32 slug.ft3 From…

Q: Required: Pump efficiency

A: efficiency = power delivered by pump / power input to pump

Q: (a) Calculate the rotor radius for a multi-blade wind turbine that operates in a wind speed of 36…

A: Given Data The speed of the wind is:V=36 km/h=10 m/s The rate is:Q=6 m3/h The lift is:hp=6m Now…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Q4/A volute centrifugal pump with an impeller diameter of 0.02 m has the following performance data
when pumping water at the best efficiency point (bep). Impeller speed N = 58.3 rev/s capacity Q = 0.012
m3/s, total head Ah = 70 m, required NPSH = 18 m, and power = 12,000 W. Evaluate the performance
data of a homologous pump with twice the impeller diameter operating at half the impeller speed, Then
Calculate the specific speed for these two pumps.
*if you know the answer is Ns1=Ns2=816.4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculation of performance data for homologous pump

VIEW

Step 3: Calculation of specific speed

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 16 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer quickly
PROBLEM 5 An axial flow pump is required to deliver 1m3/s at 7m head while running at 960 rpm. Its outer diameter is 50 and hub diameter is 25 cm. Find the following: (1) flow velocity, which is assumed to be constant from hub to tip, and A. 4.59 m/s B. 6.791 m/s C. 60.7 m/s D. 39.3 m/s (2) power required to drive the pump if overall efficiency is 84%. A. 81.75 kW B. 12.03 kW C. 40.7 kW D. 60.9 kW
Problem 2: A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: |Q-72 L/s DI = 90 mm D2 = 280 mm Flow rate Inlet diameter OUutlet diameter Нead Width at the inlet Width at the outlet Leakage Mechanical loss Blade angle at the outlet The water density Atmospheric pressure Н- 25m bl -20 mm b2 = 18 mm 9 =2 L/s Pm = 1.41 kW B: = 35 p = 998 kg/m³ 101 kPa 1) Draw the velocity triangles at the inlet and the exit of the impeller. 2) Determine the magnitude of the absolute velocity of the flow (V) and the impeller velocity (U) at the inlet and outlet 3) Determine the blade angle at the inlet. 4) Determine the hydraulic, mechanical and volumetric efficiencies. 5) Determine the minimum number of blades required for the slip to not exceed 0.9. 6) Determine the static pressure difference (P:-P1) through the impeller by using Bernoulli equation. 7) Determine the available NPSH if…
Centrifugal pump has differential pressure 15 bar and use to transport oil between two separators. If the pressure at first separator is 4 bar calculate the pressure at second separator and NPSH. Where: Suction and discharge pipe diameters = 10 inch, Suction pipe length = 16 m, ld Oil level at first separator 3 m2d Oil density=880 kg/m³ P Oil flow rate=0.092 m³/sec e Pipe roughness= 0.045 mm Discharge pipe length = 25 m O Oil level at second separator = 5.5 m2d Oil viscosity = 9.5 x 10³ Pa.s Oil vapor pressure 22.5 kPa d кра 4.5x10²
Given: Two (2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95 Bars Suction Pipe Dia = 450mm Discharge pipe Dia = 480mm Velocity of Water = 4.25 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and QT = Total Flow Rate
Problem 2 - Pumps in Parallel Two 32-in pumps, with performance curve shown below, are combined in parallel to deliver water at 60°F through 1500 ft of horizontal pipe. If f = 0.025, what pipe diameter will ensure a flow rate of 35,000 gal/min for n = 1170 rev/min? 1170 r/min 800 50 NPSH 700 600 500 400 300 200 Total head, ft 0 36-in dia. 32-in dia. 28-in dia. 4 8 82% 85% 1500 bhp 87% 88% 3000 bhp, 3500 bhp 87% 2500 bhp 2000 bhp 12 16 20 24 U.S. gallons per minute x 1000 28 8 8 8 8 NPSH, ft 40 30 20
BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 14 - 10
Hydrodynamics pumps 5. A centrifugal pump has r1 = 6 in., r2 = 12 in., b1 = 3 in., b2 = 2 in., β1 = 20°, β2 = 10° and rotates at 1200 rev/min. If the fluid is water at 60°F, estimate the theoretical (a) flow rate, in gpm; (b) the head in ft; and ( c) the water horsepower, HP. Assume near-radial entry flow. a. flow rate Answer : ____________________ gpmb. head Answer : ____________________ ftc. water horsepower Answer : ____________________ HP
Problem-3: A centrifugal pump lifts water against a static head Az = EN m. The pipe setup has a constant diameter of 0.08 m, major losses in the suction side h, = EN3 m and in the discharge side hLD is 3 m. The pump impeller has a diameter of 0.15 m, exit width of 0.015 m, exit blade angle of 22° and speed of N = 20EN rpm. The hydraulic efficiency is 0.85. If the flow at the entrance is radial, find the discharge, pump head, atmospheric pressure Pat, Vapor pressure P, and maximum allowable height of the pump from the feeding tank water surface elevation if the pump is operating under T 25 °C at altitude H= 20EN m. %3D 0, = NPSHR/Hp =1.21×10³N = (P EN=62 Is-mx at-abs-P,)/Y-hLsT -0H, Pa-abs /Y = 10.33(1– 2.256x10-H)56 P,ly = e14.29-3985(T+233.4))
A centrifugal pump is used to pump a liquid with the properties given below. Liquid is pumped from a storage tank at 95 kPa (a) to a discharge tank at 300 kPa (a). The system configuration is given in the table below. Table 1: system configuration Suction Discharge 4 50 Length (m) Diameter (m) 0.07 0.055 12 90° bends (L/D-35) 5 T piece (L/D=7) Gate valve (L/D-35) 1 1 1 2 Static height (m) 25 Liquid density = 1100 kg.m³ Viscosity = 1.5 x 10-³ Pa.s Vapour pressure of the liquid = 25 kPa (a) Material of construction of pipe is commercial steel, ε = 000045 m Table 2: Pump data 0 10 20 30 40 Flowrate (m³.hr¹) Head (m) 55 56 51 36 6 NPSH (m) 0 2 6 11 19 22 3.1. Graphically determine the optimal operating point of the pump in the above system using the pump data in Table 2. 3.2. Determine the NPSH of the system and determine whether the pump will cavitate when used in the above system.