Q4. a) Figure 3 depicts a simple DC motor, its armature winding consisting of a single turn of copper wire mounted on the rotor. The rotor core material is omitted for clarity. N GOD 富 Figure 3 Explain how the motor winding develops a rotational torque. Explain how a back-emf is produced in the rotating winding. What is the role of the split-ring commutator? The direct voltage supply to the armature is replaced with an alternating voltage source operating at 50Hz. Will the machine still rotate? Explain your answer e (i) (ii) (iii) (iv) S

Q4. a) Figure 3 depicts a simple DC motor, its armature winding consisting of a single turn of copper wire mounted on the rotor. The rotor core material is omitted for clarity. N GOD 富 Figure 3 Explain how the motor winding develops a rotational torque. Explain how a back-emf is produced in the rotating winding. What is the role of the split-ring commutator? The direct voltage supply to the armature is replaced with an alternating voltage source operating at 50Hz. Will the machine still rotate? Explain your answer e (i) (ii) (iii) (iv) S

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a DC generator, the effect of armature reaction on the main field is to * reverse it O distort it O reduce it O both (b) and (c)
The relation between armature torque and armature current of a DC motor is Parabolic Linear Inverse O Exponential
A 240 V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the ship is 6% The motor constants referred to the stator are: Stator resistance = 2-22; Rotor resistance = 3-852 Stator reactance = 3.0; Rotor reactance = 2-12 Magnetising reactance = 862; Iron and friction loss = 50 W Draw the equivalent circuit and from it find the output power and efficiency at the given loading.
Q choose the correct answer: 1-Brushless excitation system consisting of.... a- Stator field winding and power diodes b-stator and rotor field winding and capacitor c- stator and rotor field winding and capacitor d- Everything mentioned in the options 2- Voltage generated per phase in an alternator is proportional to a- Flux per pole b- Number of turns in armature c-Winding factors d- Everything mentioned in the options e- Frequency of waveform 3- If input mech. Power of SG constant, the functionality of AVR is a- Control flux of rotor b-Control terminal voltage c- Control flux and terminal voltage d-Control Load angle
A 900 rpm, 4 pole wave wound shunt motor takes 300 A. The flux per pole is 0.02 Wb and the armature has 1500 conductors. The shunt field takes 4 A of current. Solve for armature torque (Nm).
A 900 rpm, 4 pole wave wound shunt motor takes 300 A. The flux per pole is 0.02 Wb and the armature has 1500 conductors. The shunt field takes 4 A of current. Solve for power developed in the armature (W).
1. A fundamental DC motor is shown below. VTerminal = 90V. The running current, I = 5A and the rotor resistance, R = 4 ohms. Answer the following: CEMF or E at the running condition = , Power delivered by the source at the running condition = Power converted to mechanical power at the running condition Power lost in heat by the rotor resistance = Show your work for each calculation. Suggest that you clearly mark the schematic. frut
4.
Differentiate the two types of armature windings in DC machines: lap winding and wave winding.
A 4-pole dc motor has a wave wound armature with 800 conductors. The useful flux per pole is 20mWb. Calculate the torque exerted when current of 40A flows in each armature conductor.
I am in a hurry, I need the answer as soon as possible, please help.
The DC shunt generator with the terminal voltage 300 V, armature drop 9 V and the total brush drop 4 V, then the value of generated emf is