Q4) Water at 10°C flows from a large reservoir to a smaller one through a 5-cm-diämeter cast iron piping system, as shown in Fig. Determine the elevation z, for a flow rate of 6 L/s. Note that Properties The density and dynamic viscosity of water at 10 c are p-999.7 kg/m and = 1.307 x10 kg/m s.

Q: Determine the nature of flow when an oil of specific gravity 0.85 and kinematic viscosity 1.8 x 10-5…

A:

Q: For Oil (SG = 0.86, p = 0.025 Ns/m2) flow of 0.3 m3/s through a round pipe with diameter of 500 mm,…

A: Given data: The specific gravity of oil, SG = 0.86. Dynamic viscosity of the oil, µ = 0.025 N·s/m2.…

Q: Assuming laminar flows, calculate the flow rate Q of an oil flowing from tank 1 (on the left) to…

A:

Q: Elevation z₂ = 0 (2) B Total length = 510 m D Elevation ₁ = 13 m (1) ▼ A

A:

Q: Two piezometers (manometers) are placed 1.5m apart in a horizontal plastic pipe as shown in figure.…

A:

Q: A patient receives IV fluid through a needle of radius 0.200 mm and length 2.0 cm. The density of…

A:

Q: True/False: For saturated water with a quality 0 < x < 1, volumetric flow rate can be used to…

A: The process given in the question is accompanied to change of water from saturated water to…

Q: A fluid of viscosity μ flows in the horizontal cylinder (radius R) shown in the figure under a…

A: The viscosity of the flow is, The velocity at the porous region is, The radius of the porous region…

Q: 26 Ps Water Water Oil Manometric fluid Manometric fluid Find the pressure difference at two points A…

A:

Q: Oil, with kinematic viscosity of 0.001 m²/s is flowing inside the pipe network shown. The internal…

A:

Q: pipe with a velocity of 20mm/s. What is the pressure difference between the point of entry to the…

A:

Q: Q4. For fully developed flow in a pipe, the head loss due to friction ( h,) is given by the Darcy-…

A:

Q: An oil (viscosity 1 Pa.s, density 800kg/m3) is flowing in an axisymmetric pipe. The flow is fully…

A:

Q: In fluid mechanics, The minor losses occur due to any disturbance that might occur to the flow,…

A:

Q: A mercury manometer installed across an orifice meter (diameter = 1.2 cm) in a horizontal pipe…

A: Given: d = 1.2 cm = 0.012 mD = 2.35 cm = 0.0235 mh = 12 cm = 0.12 m Taking the density of mercury as…

Q: 1. Fuel flows through a pipe from a pressurized vessel to an open tank at a rate of 2.3 m³ /min (see…

A:

Q: A layer of Oil of specific gravity SG = 0.85 and dynamic viscosity µ = 0.123 Pa.s flows steadily…

A: Given dataSpecific gravity of oil SG = 0.85Dynamic viscosity μ = 0.123Pa.secInclination of street θ…

Q: Verify that the flow of oil is laminar (barely) for an oil gusher that shoots crude oil 25.0 m into…

A: Understand that at the topmost point the velocity of the water stream will be zero and the water…

Q: A Venturi meter is being used to determine the flow of soybean oil at 65 °C in a pipe. The…

A: Ans Given Now calculate the inlet cross-sectional area of pipe as Again calculate the outlet…

Q: A viscous Newtonian fluid is flowing in a horizontal rectangular duct with dimensions, L=10 m, W=1 m…

A:

Q: A petroleum liquid with (SG = 0.95), flows through the Venturi meter as shown with flowrates between…

A:

Q: The mean volume flow rate in the femoral artery is 5 ml/s. The length of the femoral artery is 18 cm…

A: Given: Mean flow rate; Q =5 ml/s =5 *10-6 m3/s Length; L =18 cm =0.18 m Diameter; D =1cm =0.01 m…

Q: the pressure at

A: given:ρw=density of water=1000kg/m3ρoil=0.90×1000=900kg/m3PB=8KPa

Q: An upright hollow brass cylinder, inner radius = 5 cm and outer diameter = 18 cm, is 30 cm tall. If…

A: To Find : The angle at which its slants. Given : The inner radius f hollow cylinder is The outer…

Q: 2. For a piping system as shown in the figure, determine the distribution of the water flow Qi and…

A:

Q: An engineer monitored a flow of gasoline of about 50 m3/h and of density ,ρ 680 kg/m3 through a…

A: Solution: Given Data: Q=50 m3/hρ=680 kg/m3D=10 cmd=5 cmμ=2.92×10-4 kg/m-s   To Find: Which device is…

Q: . Two reservoirs containing water (density of 1.94 slug/ft³ and molecular viscosity of 2.09 x 10-5…

A: The diameter of pipe 1 is d1=1 in.The length of pipe 1 is l1=20 ft.The diameter of pipe 2 is d2=2…

Q: For the piping system of Fig. , all pipes are concretewith a roughness of 0.04 in. Neglecting minor…

A: For water at 20°C, take ρ=1.94 slug/ft3 and μ= 2.09E−5 slug/ft⋅s. Since the pipes are all different…

Q: A pipeline 0.5 m diameter and 1200 m long is used for transporting an oil of density 150 kg/m3 and…

A: Write the given data.  d=0.5 m L=1200 m ρ=150 kg/m3Q=0.4 m3/s μ=0.91 Pa·s Here, d is the pipe…

Q: A petroleum liquid with (SG = 0.83), flows through the Venturi meter as shown with flowrates between…

A: Given:Specific gravity of liquid, s=0.83Velocity of liquid at point 1, v1=4 L/sVelocity of liquid at…

Q: The water flow between large tanks is steady and steady, and the pipe diameters are indicated in the…

A: hB=2mg=9.81 m/s2ρ=1000 kg/m2d2=0.03md4=0.05m

Q: Given an open tank filled with oil that is discharging through a 35-meter long commercial annulus…

A: GivenRi=2cm=0.02mdi=0.04mh=5mS.G=0.9L=35mμk=4×10-5 m2/s

Q: Fluid originally flows through a tube at a rate of 100 cm3 /s . To illustrate the sensitivity of…

A: 'Since you have posted a question with multiple subparts. we will solve the first three sub-parts…

Q: If the difference between the total pressure and static pressure in an air duct is measured by a…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.